Jump to content
SAU Community

Recommended Posts

I don't know either.

but my experience has been that as long as it is never registered, no-one tracks the car once it arrives.

but again, if you want something for parts surely a half cut is better, cheaper to buy and import and will probably have all the bits you need.

ok, i think its a 1995 rx7, you can only import them for race/rally use...

now, u can import one for about $13000 or cheaper

and in australia they are $30-50000

so if you have lets say a bare shell thats road legal in australia, would taking out the whole of the import and putting it into the aussie car make it legal?

yea i been dreaming about importing series 6-7 exracer rx7. i think you need a ANDRA licences but you could drive it on the road, (in wa) anyway with $12 permit's they only last 48hours so just pick one up every friday arvo and kill everyone on crusies on the weekends. also dont need to have number plates. prob wouldnt happen but its my dream.

so you can do that?

you can buy a race / rally use import, and swap everything into an australian road registered car and itll be legal?

thanks

No you cant do it as the motor is never to be in any other vehicle.

RX7's arent on the FIA list so you have to get a letter from CAMS to bring one in as of the last month.

They are cracking down big time.

nope, the car was under the old LEV scheme and the engine from a half cut...but of course the people who inspected for the blue slip didn't know where the engine came from.

My rally gtr on the other hand has been sitting around with a blown engine for about 6 months and is about to get a new one, but then that engine will be rebuilt and used elsewhere....I'm pretty sure there is no rule about how a part (eg engine) can be used once it has arrived in aus.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are a few different ways of doing it. I'm currently running two 1000cc pre-TB nozzles and PWM the pump for control. I'll be moving over to a constant pressure system and direct port. I'll run the pump off a regular relay, have it cycle on roughly 5psi before I start injecting to build pressure and then PWM a WMI solenoid (It's basically an injector that can take a lot of pressure and not corrode with water and meth.) The solenoid feeds the 6 direct port ~200cc nozzles. I'll also keep one ~250cc pre-TB nozzle to help keep IAT's in check.  Safety will be a little different as well. I used to use a pressure switch but will be moving over to a pressure sensor between my solenoid and nozzles. I'll trigger my solenoid and if I don't see specific pressure within a specific timeframe (e.g 100psi within a second, 175psi within 2 seconds), I kill it and revert back to non WMI maps the same way I did it before with 4D in Haltech. I was just figuring out the timers in my ecu last night. They made that a little more complicated than I would have liked... I wish Haltech offered a larger set of logic/math functions like other ecu's do. I can't do very much with just AND's and OR's.  I've been asked to do fuel/ignition mapping on a medium bore engine at work in May (192L V16). Being the only programmer in my region and having went and opened my mouth about knowing the ins and outs of fuel/ignition mapping, I have now been deemed an expert. Fun fun. The entirety of the logic and algorithms are programmed in C on a PLC. As I spend more time figuring it all out, I like what I see and eventually I may consider doing the same as a pet project to replace my ecu.   
    • This would be interesting, would you feed it via a 2nd row of injectors? Or just usual WMI nozzles?
    • Cut sump up and extend. Win win 😂 
    • All, What's the recommended torque for the 1/2 head studs for RB30 twin cam conversion with RB26 head?  
    • also, we need to know which solution worked....
×
×
  • Create New...