Jump to content
SAU Community

Recommended Posts

Hi guys,

I've seen some skylines around with what I assume to be "Locked Diffs" they make this skipping noise of the inside wheel while turning tight corners.....

... first of all, is this safe for daily driving ?

Does anyone here recommend a locked diff brand/type ? Are there switchable diffs to lock/unlock them ?

What's wrong with the standard LSD that comes with Skylines ? Or was it an option?

And what exactly is an active LSD ?

Are you able to lock a standard skyline diff ?

I have Active LSD on my R33 SII GTS-25T and this is what I know about it and it aint much.

The Active-LSD uses a computer to sense wheel slipage and diverts power to the aposing wheel rather than by mechanical methods, the main difference is the speed that is can tranfer power from wheel to wheel. 1/50 sec. It uses a similar system to the 4WD system on the GTR but only transfers power from side to side.

I've got a mechanical in mine and your right, they are a bit noisey around tight slow corners. But apparently they give you the best grip for a (two wheel drive) rwd car.

Straight line drags are great, corners are a bit strange at first, but once you realise that they are very pradictable your OK.

They really aren't as bad as everyone says they are in the wet either.

J

Originally posted by tlai909

Do all Skyline r33 models have the basic mechanical LSD?

T.

All turbo R33's have LSD as standard. But mechanical locking LSD's are an after market thing.

Some loucky people got the Active LSD's, they are again different to normal LSD and mechanical locking LSD's.

Sooooooo many diff's.........

J

  • 6 months later...
  • 2 weeks later...

I'm looking at getting a manual r33 sedan still deciding on turbo or not.

so does that mean a turbo sedan will have a viscous LSD and a non turbo wont have LSD?

can someone clear it up for me please.

Yeah, standard diff is viscous.

Viscous diff uses property of the oil to limit slip - as slip occurs it get stickier. quickly.

The active diffs use sensors on the wheels, and electronically controlled clutches to control torque - just like the front to rear split in atessa.

with the mechanical... so it locks under power ?

That sounds good... The wet wouldn't bother me as my car is nasty as it is so i take it easy.

But it can be a little unpredicatble at times, so J, if as you said it makes it more predictable ?? Then i would want that.

And that's good for drifiting isn't it ? That's what i'm aiming for over the next 2-3 years as a project!

R31 - yepp, you've hit the nail on the head. From my limited experience (cause I drive like a granpa most the time!), when the back comes around it's very predictable.

From what I've read, the mechanicals are great for drags and trackwork, and even better for drift. They can be a bit noisey for street driving. Some days it pi$$es me off, but other days I think 'damn I love this diff !!'

Like last night overtaking someone doing 70 in a 80 zone... Raining... I drop it back to 3rd and give it 1/2 throttle. It starts spinning the wheels but it still holds a dead straight line.... Unless you flick the wheel a bit of course :)

Meg's - does your's clunk (inside wheel skip) around tight corners when you give it a bit of throttle?

GaryD - Mechanicals only lock up when the throttle is pressed, so they are sort of open wheeler diffs until you give it some go.

The reason why they are good for track work is cause instead of pulling hard out of corner from just before the apex and spinning the inside wheel (typical for even LSD diffs) they will power around with both wheels with a bit of oversteer.

But the oversteer isn't massive and is very easily controlled. Infact most, if not all V8 supercars use either locked or mechanical lockers of some sort.

I was up at Wakefield last friday watching the Brute Utes have a pratice, and as they were coming into the workshop area all of them were skipping the inside wheel while turning tight and slow....

J

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You’ll want to have the block drilled and tapped to suit 1/2in head studs and the head for the same. How much power do you intend to make?
    • Sorry for resurrecting an oldish thread Not much has happened in the past year since the last update. The car did another 1000 miles or so and failed the MOT for the first time in October (failed on tyres which had been advised for a couple of years) In October the car got put up for sale and was removed in November due to no interest, being so close to christmas it was to be expected. The roads were dry in February so I decided to tax it early and get the new tyres fitted.   Fast forward to April, I got someone in to give the car a good clean after sitting for the winter.                                 The car got re-advertised and today (Saturday 3rd May) the car sold. The new owner is planning a GTR conversion at some point and a respray in the same pearl white. It's bitter sweet, it's a shame to have the car sit there for half the year and then only do 1000 miles. The kids are growing too quick and space in the back is getting limited. It's been a great 6.5 years of ownership
    • And if you want more power, more reliably, and cheaper, go get the Aussie RB... The 4L Barra and put that in instead.
    • No cats will keep discolouring the rear bar. Sends white paint a weird yellow stain. Cut and polish normally gets it out, but you'll be doing that every fortnight I found.
    • Both heads will be equally reliable or unreliable depending on what you do to them.  Stock the RB26 head will flow more. You have access to the stock intake ITB manifold on the RB26 cheaply which flows really well(1000hp+).   Arguably more aftermarket support for RB26, though in Aus we love our RB30 SOHC heads too.    The only downsides to the RB26 head is if you have a VL commodore and want to keep the SOHC look.  Where you may have an issue is drilling out the rb30 block for the bigger head studs but if you are building a big power motor you'd probably put bigger studs on the SOHC head too.  This is just about finding a good machine shop, sometimes easier said than done.  RB30 head worked can make big power just like a Rb26 head, so really it actually more comes down to what your preference is for your car.  People now even making billet versions of both.
×
×
  • Create New...