Jump to content
SAU Community

Recommended Posts

HELP!!!

I've finally put the bilstein's in, but the spring hat on the drivers rear side is rubbing slightly on the tyre.

Apart from raising the car up (its on circlip groove 3 from bottom), is there anyway l can fix this? Its not rubbing much, so will l just wear part of the tyre away before it stops rubbing, or could things get worse.

not a good idea to add positive camber that will wreck your tyres assuming you are running it on the road.

what you really need is wheel spacers, or even better a different offset wheel to clear it properly

don't run it as is, rubbing the tyre is bad news

nooooooooooo

not literally POSITIVE camber

i meant as in adjust your factory camber arm to move it out a bit.

Not like +camber..my bad.

i mena, if its just lightly rubbing, a small camber adjustment might fix it

but like duncan said, a lower offset wheel will fix all

  • 3 weeks later...

my stagea has nismo s-tune suspension. is this height adjustable in any way? or can it be adapted to be height adjustable? im pretty sure it is damper adjustable, looking at the strut tops (there is a numbered dial on top).

Any help would be appreciated.

as in circlip grooves like SK's whiteline/bilstein kits? I will check it out.

Anyone have much experience with nismo s-tunes? decent suspension....?

Car got a few things from the nismo brochure it turns out - S-Tune filter, S-tune suspension, nismo clutch and nismo badging.

  • 3 weeks later...

just finished reading through all 25 pages and man do i have a headache :D

now forgive me for being such a n00b but there hasnt been much talk on

an actual set of coilovers for the stagea....anyone have any ideas?

i dont actually have my stagea yet, she's still on her way over from japan,

so obviously i havent had a chance to look under her yet. But basically i like

my cars low, not ridiculously low but possibly more than your average user.

Is this attainable on the stagea's? Because from what i read it doesnt appear

as simple as some other cars might be. Oh my stagea is a S2 99 RS Four S,

and i know the restriction to do with the exhaust but any other major issues

apart from that? Also i had tein superstreet coilovers in my last car (13b s13)

and i didnt find them uncomfortable at all, and they were adjusted fairly stiff.

So back on point anyone know of or using coilovers in their stagea? Was

wondering on those G4's from just jap as i heard they are quite adjustable....

Tein make 3 different setups that I know of for the stagea. I was looking to go down this path but so many people have recomended SK's kit that I decided to go with that. Would rather go with something thats been tried and tested here on Australian roads. You've got to remember that the Stagea is no 1400Kgish S13 either. And although you could technically buy a mixed set of coilovers (GTR front and GTST rear) from any brand like has been said in this thread many times the front will be ok more than likley but the valving and spring rates for the rear will not.

If the only thing your looking to do is get your car as low as you can go if you order the kit off SK you can get even more circlip grooves machined in but you'll sacrafice handling. One other forum member had this done if you read back in the first couple of pages of the Suspension Group Buy Thread.

And as for the G4 coilovers from Justjap I don't think they do anything stagea specific. Look at nengun.com and you'll find a few sets for the stagea.

I think its going to be a harsh ride 10k font 8k rear, but I'm no suspesion expert either. Others here would be better qualified but I also know what they're going to say :blink: You should read what others have said about running jap spec coil overs on stageas here in Aus. Some ended up swapping them out for something else. If your set on coilovers I'd look at some of the Tein Wagon series, they have lower rates which would be better for street use I think.

Also while I'm at it. When all my parts get here I'm doing a complete brake overhaul on my series 1. The only thing I haven't sorted out is the brake shoes for the hand brake setup. Does anyone know the part numbers, availability and how easy they are to do. Never done them before?

just finished reading through all 25 pages and man do i have a headache :thumbsup:

now forgive me for being such a n00b but there hasnt been much talk on

an actual set of coilovers for the stagea....anyone have any ideas?

i dont actually have my stagea yet, she's still on her way over from japan,

so obviously i havent had a chance to look under her yet. But basically i like

my cars low, not ridiculously low but possibly more than your average user.

Is this attainable on the stagea's? Because from what i read it doesnt appear

as simple as some other cars might be. Oh my stagea is a S2 99 RS Four S,

and i know the restriction to do with the exhaust but any other major issues

apart from that? Also i had tein superstreet coilovers in my last car (13b s13)

and i didnt find them uncomfortable at all, and they were adjusted fairly stiff.

So back on point anyone know of or using coilovers in their stagea? Was

wondering on those G4's from just jap as i heard they are quite adjustable....

Welcome to the Stagea section, Alex! I see you got your name change request done... :(

Anyway, onto your question, about a month before I came and met up with you, I had the Sydneykid kit installed onto my car, and I love it! It's not adjustable for damping, but the ride height can be changed with the circlip grooves as Josh has mentioned. The valve rates have been set up by Sydneykid to suit our roads, and although it is a bit bumpier than the standard set-up, it's by no means harsh compared to what the rates on those Teins would probably be like. If you do want to go with a set of Teins, most people here would probably recommend the Super Streets.

*Also, when you do order your suspension (whichever way you decide to go), then make sure you specify that yours is the factory manual, as the rear suspension sub-frame is different to the auto models.* I believe, from memory, that the RS Four S has an R33 GT-R sub-frame rather than the R33 GTSt one.

Nick

Thanks Nick,

Most helpful as usual. What do you think of Buddy Club vs Tein? Can i use those whiteline swaybars as well? Like i said i'm a total n00b

when it comes to these things, prior to my Silvia i'd only had Gemini's and the like, and they were lowered courtesy of Angle Grinder

Performance hahaha! Also another question relating to wheels/suspension, the wheels im looking to get are 19's, and come in either

19x8 or 19x9.5. Would either of these have issues fitting with the suspension? And as long as the total outer diameter is the same, can

i put on 19x8 at the front and 19x9.5 on the back, or does this cause issues with the AWD regardless? Sorry if these are silly questions

but if you dont ask you dont know!

Alex

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update: I got the magnet out. I bought 3 different flexible magnetic reach tools, but none of them worked. The magnet on the tip was all less than 2lbs of force, so i had to buy a special cylindrical magnet that had a pull force of 9lbs.  The magnet finally came in the mail yesterday, so i got under the car to get to work. The super strong magnet isn't that long, so i only have about 1 finger pinch lengths to hold it. I was so scared when i was going in the hole, that the 9lb magnet would just fly away inside the oil pan never to be seen again, but i had my butt cheeks clenched and finger gripped on that thing so tight, i managed to get it to suck the other magnet out.  It was a victory for me last night.         
    • Yep, pretty much what you said is a good summary. The aftermarket thing just attached to the rim, then has two lines out to valve stems, one to inner wheel, one to outer wheel. Some of the systems even start to air up as you head towards highway speed. IE, you're in the logging tracks, then as speeds increase it knows you're on tarmac and airs up so the driver doesn't even have to remember. I bet the ones that need driver intervention to air up end up seeing a lot more tyre wear from "forest pressures" in use on the highway!
    • Yes, but you need to do these type certifications for tuning parts. That is the absurd part here. Meaning tuning parts are very costly (generally speaking) as well as the technical test documentation for say a turbo swap with more power. It just makes modifying everything crazy expensive and complicated. That bracket has been lost in translation many years ago I assume, it was not there.
    • Hahaha, yeah.... not what you'd call a tamper-proof design.... but yes, with the truck setup, the lines are always connected, but typically they sit just inside the plane of the rear metal mudguards, so if you clear the guards you clear the lines as well. Not rogue 4WD tracks with tree branches and bushes everywhere, ready to hook-up an air hose. You can do it externally like a mod, but dedicated setups air-pressurize the undriven hubs, and on driven axles you can do the same thing, or pressurize the axles (lots of designs out there for this idea)... https://www.trtaustralia.com.au/traction-air-cti-system/  for example.... ..the trouble I've got here... wrt the bimmer ad... is the last bit...they don't want to show it spinning, do they.... give all the illusion that things are moving...but no...and what the hell tyre profile is that?...25??? ...far kernel, rims would be dead inside 10klms on most roads around here.... 😃
    • You're just describing how type certification works. Personally I would be shocked to discover that catalytic converter is not in the stock mounting position. Is there a bracket on the transfer case holding the catalytic converter and front pipe together? If so, it should be in stock position. 
×
×
  • Create New...