Jump to content
SAU Community

Recommended Posts

Started doing the headlights today as I was taking off my indicators and front bumper to do the widebody kit measurements and also the custom air intakes in the indicators.

Will post up pics soon.

Idea is to make up custom headlights. I have 2 pairs of headlights, one are the 89 model poverty lights that I bought on here, the other are the late model ones that came with my car (got the GTR ones coz my car was a V Selection II) should be very similar to the Series 2 R32 headlights anyways.

Things to do for:

89 Model headlights...

The headlight was shipped in dodgy packaging so the glass on the RHS one was smashed to bits (cut my hand on it when I opened the packaging). Anyways, after cleaning off all the glass shards on it, I took off all the rubber grommets and clips, took out the bulbs and plugs.

Then i unclipped the 4 metal clips holding the glass onto the headlight.

It was 32 degrees today in the sun, so I put the headlight in the sun to heat up naturally. I did this because I didn't want the glass from cold to hot and shatter (well it was already shattered, but it was practice for the non shattered ones).

I got an oil pan, filled it with boiling water and then dipped the glass side in and left it for 10 mins to heat up. THen using a screw driver I gently pryed the glass of the headlight. It was pretty easy to do since the glass was broken into chunks.

After this i found there was shattered glass in the glue, so while it was hot I quickly cleaned all that out too.

Then I took out the internals, and seperated everything.

Next thing to do:

Undid the headlight on my car and put the shell into it, checked where there was space to do more in, not really much space to do anything because of the aircon hoses etc.

Cut out the back of the headlight. THis should allow me more freedon to do extra shit in it.

Make up cardboard contour cards of the general shape I wanna get, put the replacement bulbs in and get a feel for the reflectors etc.

Block off all the bits I don't want affected, lay clingwrap on the surface then fill the headlight with space invader. Once the space invader has foamed out, carve the general shape I want out of it. Then pull the whole thing out using the cling wrap.

Using the solid block of dried space invader, create a cast by laying fibreglass on it. Once the cast is set, then use the cast to create a gelcoat negative which I'll then paint and put back into the headlight. Then make up the reflectors (either thin aluminium sheets, or chrome paint). Once all that's done, fabricate a cover using fibreglass and heat resistant perspex or glass (depending on what I can source). Then repeat steps for the other headlight.

Link to comment
https://www.sau.com.au/forums/topic/53353-r32-headlights-customising/
Share on other sites

i dont understand what you are trying to achieve....are you just putting different type lights behind the stock 32 glass, or what....if you are tryin to do a twin headlight conversion, you can buy them.

Hi - Maybe you can help me. I'm looking for twin headlight projector lights like the ones on the "Flybye" in the 2004 Autosalon car of the year mag. I called Autostyle who tell me they make them and will not retail them.

Any suggestions

With my current headlight (the Series 2 GTR ones)...

I took out the left one (and replaced it with the unbroken 89 left headlight... so now I'm driving around with a Series 2 RHD light and a series 1 LHD ligh, looks very odd but shmeh)

Using the same process I took out all the bulbs n clips n screws n grommets n vent hoses. Then left it in the sun to heat up. Then put it in a hot water bath to heat up further. After 10 mins used a thin screwdriver to make a small wedge into the headlight and pull out a corner. after this I used a knife to cut back the black goo a lil, and the back of a teaspoon to wedge it out some more, repeat that again and again, till the whole glass was out of the plastic casing. The trick is not to get too excited when you get a lil bit of movement as the glass can very easily crack.

Here's the disassembled headlight...

headlight_01.jpg

This one has a projector lense in it, so I don't intend to customise it to extremes. It has a chrome silver shroud that I'm gonna paint matt black. And then put a Xenon HID conversion kit in. Put it back in the car and test em out. With R32s projectors and Xenon HIDs I read in jap mags that the xenon bulbs tend to form shadows in the beam that they project... like so...

headlight_04.jpg

See how the bulbs form shadows...

Some of them have managed to modify the shadow so that it looks like so...

headlight_02.jpg

Here's what the HID light looks like on the projector style headlight...

headlight_03.jpg

Hopefully I can figure out a way of getting rid of the shadow cast by the bulb (due to internal light reflection). Painting the shroud in black "should" fix it, but we'll see how it goes.

Um, Autostyle are wanks :P if they don't want to sell to the public

1803.jpg

If you're talking about the headlight kit in this thing, I've had one, and its really dodgy, for one its exposed to the elements, and secondly the backing on it is absolutely POS. I got mine from japan from the manufacturers after a lot of begging and pleading. I've posted up pics of it before on the forums. Add to this the fact that if you get really close to it it looks butt ugly due to the metal bracket showing thru and having a very ugly looking contourless 90 degree bend in it. If you're still keen on em, then I've got the moulds for it and it shouldn't be that hard to get someone to make up a batch of em.

Basically I'm trying to get an H4 dual beam (highbeam/lowbeam) Xenon HID, H1 Xenon HID projector, and indicator setup with clear glass front setup on the 89 headlights and a standard Xenon HID only setup on the Series 2 headlights. Both with no bulb shadows and clear front glass. With the Series 2 headlights I might take t to a glass blower, and get them to place the glass in high heat sand and then put it in the kiln to heat it up and get rid of the diffractors. Failing that I'll just use perspex or clear glass that I fabricate using the 89 headlights.

Time for a bit of Mythbusting...

"Autostyle headlights" are NOT what they should be known as... they are in fact Infinty Headlights...

Here is their website: http://www.info-nagano.co.jp/infinity

One of the guys at autostyle just happened to import his car with these on, and suddenly that's what they're called... pfft.

index_007-Opt.gif

prt_mr4t-R32-hdl.JPG

they also do them for S14's prt_mr4t-S14-hdl.JPG

Here's the pair of INFINTY headlights that I bought:

aftermarket_headlamp1.jpg

aftermarket_headlamp2.jpg

its not the hardest to clone nor the most complex headlight in the world... if you're a fan of getting your bulbs a bit too close to getting wet in the rain... go nuts.

Anyways, back on topic, I'll post pics of the headlight customising tomorrow sometime.

Funky

Firstly, sounds a good little project. Let me know if you are intersted in trying them in carbon at all (if you dont have access to carbon yourself already that is).

Secondly, I have a early projector on the drivers side & a late projecter on the passenger side. Wanna swap so we have matching sets of lights?

Ben

Um I have 2 pairs of lights, so I have complete sets :D sorry dude, but I can get you a headlight if you want from a wrecker.

Carbon sounds interesting... I was thinking about it... I can do very very bad CFing using a vaccumn pump and a thick plastic bag :D do you know someone that can use my moulds to make some CF items? I've never made a mould for CF, is there any special requiremens or is it the same as gelcoat moulds?

buggar about the light... :D

The main probs with moulding in carbon is getting the woven mat to stick in small areas and tight complex curves. Obviously, with a clear top coat, any parts where the weave pulls or gets a little distant from the mould show up on the surface.

When you've got the moulds set up & ready, take a few good shots of them and I'll run the pics past the CRP mob I know and see what they say.

PM me if you want my email

Ben

.

Hey that sounds like a great project funky. I have no idea why you're doin what you are but I've been thinking of pulling apart the ceffy headlights to give them an angel eye (yes rice I know but original also and with the dual projector lights i don't think it will look too bad!!).

The other idea was to drill a shaft between the two projectors and mount a small orange light there for an indicator (my bar doesnt have any).

Anyways so this gives me a way to open the headlight enclosure without snapping it because I wasn't sure how to take them apart so thanks for that.

Just out of interest if you drop them in hot water after warming them up gently are they watertight at the front? To be it seems obviously yes they are but just to confirm.

How much the HID cost you? Let me know if you figure out the HID retrofit cos the ceffy and r32 projectors look identical.

Thanks.

someonestolecc, the ceffy's headlights are next on my list of things to do, rip em apart, take out the pooncy yellow fogs, paint the backing strip matt black, then do angel eyes on the dual projectors. I'll then rewire the fog lights to an H4 halogen, to use as high beam (and blind the f**k out of everyone in the process).

I'll be doing dual xenon's on them too (providing my old man forks over enough for it) otherwise I'll just go with hi temp halogens.

And yes they are GTR headlights I'm chopping, they came standard with my car.

I'm using a water resistant clear sealant (Selley All Clear) to reseal it.

Don't drop em straight in hotwater as the glass might crack due to the extreme change in temp. And yeah they are watertight. so you put it in the bath and you pour some hot water inside the headlight case.

Nice funky.

I like my yellow fogs I think I'll keep them - but definately the ceff DOES need HID the headlights are shocking. That's an interesting idea .. double low beams and the foggies turn into the high beam.

Doesn't that mean you need 4 ballasts and 4 HID bulbs? Sounds like over a $1000 for the conversion there :

Are there any where in Japan that do out-of-the-box HID conversions for ceffies? Where are you sourcing your HID from? Last I saw phillips ballasts + globes were like min. $600.

I think all R32 & R33 skyline headlights (except for the Xenon set) are pretty crap... ordinary throw and not bright enough :P

Might have to invest in some HIDs as they fall in price

PS and those round headlights are damn butt ugly!! Can't they even get the fibreglass surround straight at the bottom, side and top edges?!? :fart:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, all the crude is used for fuels and petrochem feedstocks (pesticides, many other chemicals, etc etc). But increasingly over the last few decades, much of the petrochem synthessis has started with methane because NG has been cheaper than oil, cleaner and easier and more consistent to work with, etc etc etc. So it's really had to say what the fraction either way is. Suffice to say - the direct fuels fraction is not insigificant. Heavy transport uses excruciatingly large amounts. Diesel is wasted in jet heaters in North American garages and workshops, thrown down drill holes in quarries, pissed all over the wall to provide electricity to certain outback communities, etc etc. Obviously road transport, and our pet project, recreational consumption camouflaged as road transport, is a smaller fraction of the total liquid HC consumption again. If you're talking aboust Aussie cars' contribution to the absolute total CO2 production of the country, then of course our share of the cubic mile of coal that is used for power generation, metallurgy, etc adds up to a big chunk. Then there is the consumption of timber. Did you know that the production of silicon metal, for example, is done in Australia by using hardwood? And f**king lots and lots and lots of hardwood at that. Until recently, it was f**king jarrah! There are many such sneaky contributors to CO2 production in industry and farming. NG is used in massive quantities in Australia, for power gen, for running huge water pumps (like, 1-2MW sized caterpillar V16 engines running flat out pumping water) for places like mine sites and minerals/metals refineries. And there are just a huge number of those sort of things going on quietly in the background. So NG use is a big fraction of total CO2 production here. I mean, shit, I personally design burners that are used in furnaces here in Oz that use multiple MW of gas all day every day. The largest such that I've done (not here in Oz) was rated to 150MW. One. Single. Gas burner. In a cement clinker kiln. There are thousands of such things out there in the world. There are double digits of them just here in Oz. (OK< just barely double digits now that a lot of them have shut - and they are all <100MW). But it's all the same to me. People in the car world (like this forum's users) would like to think that you only have to create an industrial capability to replace the fuel that they will be using in 10 years time, and imagine that everyone else will be driving EVs. And while the latter part of that is largely true, the liquid HC fuel industry as a whole is so much more massive than the bit used for cars, that there will be no commercial pressure to produce "renewable" "synthetic" fuels just for cars, when 100x that much would still be being burnt straight from the well. You have to replace it all, or you're not doing what is required. And then you get back to my massive numbers. People don't handle massive numbers at all well. Once you get past about 7 or 8 zeros, it becomes meaningless for most people.
    • @GTSBoy out of the cubic mile of crude oil we burn each year, I wonder how much of that is actually used for providing petrol and diesel.   From memory the figure for cars in Australia, is that they only add up to about 2 to 3% of our CO2 production. Which means something else here is burning a shit tonne of stuff to make CO2, and we're not really straight up burning oil everywhere, so our CO2 production is coming from elsewhere too.   Also we should totally just run thermal energy from deep in the ground. That way we can start to cool the inside of the planet and reverse global warming (PS, this last paragraph is a total piss take)
    • As somebody who works in the energy sector and lives in a subzero climate, i'm convinced EV's will never be the bulk of our transport.  EV battery and vehicle companies over here have been going bankrupt on a weekly basis the last year. 
    • With all the rust on those R32s, how can it even support all the extra weight requirements. Probably end up handling as well as a 1990s Ford Falcon Taxi.
    • Yes...but look at the numbers. There is a tiny tiny fraction of the number of Joules available, compared to what is used/needed. Just because things are "possible" doesn't make them meaningful.
×
×
  • Create New...