Jump to content
SAU Community

R33 boot floor template.

JimX

By JimX,
in General Maintenance

 Share

Recommended Posts

JimX Grand Master

JimX

Posted
Posted

I'm going to design my own boot floor template so I can make one out of MDF. The factory one doesn't even fit properly! It uses bits of foam to rest on the spare tyre (which I've removed) and the rest of it doesn't appear to line up with any of the ridges in tbe boot.

Before I go ahead and do this though, I just wanted to know if anyone else has done this before? I basically want a snug fit into the indentations around the spare tyre well so it won't move around, and I can then bolt a sub to it (or at least clip it on for easier removal of the 2 separate items). I also want to make it a lot sturdier than the factory cardboard stuff so that it doesn't require the spare tyre to give it stability.

If no one's done it I'll just do my own from scratch and upload the finalised plans for anyone interested.

Link to comment
https://www.sau.com.au/forums/topic/5338-r33-boot-floor-template/
Share on other sites
JimX Grand Master

JimX

Posted
  • Author
Posted

I'll see if I can get some measurements on the weekend, and hopefully buy the MDF too. I'm going to make it as thin as possible while still making it sturdy, because I don't want it coming through the rear seat panel and slicing my passengers in half! :eek1:

I don't think I'll be able to actually make it this weekend though, I still need to find a jigsaw. A friend of mine who had one moved to England recently :D I'll tell you how I go on the weekend.

JimX Grand Master

JimX

Posted
  • Author
Posted

Well I had a good look the other day and I don't know how this is going to work. There doesn't appear to be any lip around the edge for the floor to sit in.

What I might do is make something with legs on it so that it sits inside the spare tyre well, but I don't know if this is going to work if the spare tyre is in there.

Ah, I just had a brainstorm! Instead of legs to support the whole thing from the bottom of the tyre well, maybe just little bits of wood to keep it in place around the lip of the well to stop it sliding around. Then the actual floor itself can be any shape at all and it shouldn't shift around.

Anyway I'll see what I can figure out eventually.

JimX Grand Master

JimX

Posted
  • Author
Posted

Yep, as does the factory item. I'm just hoping to design it so that it won't jump around too much and if it does it will land back where it started. Perhaps some foam underneath to help absorb any clunking sounds, or even velcro to hold it down? I could always use nut and bolt type fasteners or clips, but that'd probably mean drilling into the floor of the boot and I definitely don't want to do that.

This is turning into a major project, why couldn't they just design something good from the factory? (sigh)

Guest DON91E

Guest DON91E

Posted
Posted

Hey JimX,

I actually did this on my first R33, Didn't take down measurements of anyting but ;(

I would be planning to do something on mine for a while too :D

What i would do is get the original carpet, put it over a piece of MDF or watever you wanna use, trace around it with a pencil, and then start jigsawing :)

To stop it from boucing i would then goto HARDWARE HOUSE and buy some of that Velcro thats double side..(make sense?) the Velcro was $5.00 a meter i belive.

then stick one side of the Velcro down to the floor and then one on the actual MDF.

As for spare tire issue, i would just get some foam from clark rubber and fill it up to be the same hieght as the rest of floor.

I also wanted to make one for the rear, battery cover thing, pretty str8 forward that one but things is how to mount is.

As i wanted to have my AMP secure on to there.

Let me know how u go,

If i get bored i mite start making one... :)

DOnnie

_turtle_ Proficient

_turtle_

Posted
Posted

couple of months back i took out the spare tyre and drove around without it. then i had to do some grocery shopping, buy some drinks and stuff like that. couldn't put it on top! coz the covering that is there is so weak that it just caves in!

so yer, i reckon this thing is a good idea. i'd be interested in it.

i don't think it bounces around that much with the carpet covering it.

ix9 Grand Master

ix9

Posted
Posted

I'll vouch for the "tracing around the carpet" idea..

I did this in my sonata to construct a new boot floor. and it works a charm, i user 12mm MDF, sturdy as a rock!

I sunk my amp into the tyre well, flush with perspex and neon's to the floor.

I then had the 2x12's facing the back of the car, pretty much where the flimsy battery cover thinggy is in the Skyline....

Don't forget to secure the MDF to the boot floor. Velco still lets it move around a bit and didnt work for me... I just used countersunk self-tappers, then carpeted over it all in light grey..

looks the sh*t too :)

If your going to use a sub in there, ply wood is ghey, it's too thin and rattles VERY easily...

Good luck guys..

-Kym

The Tool Enthusiast

The Tool

Posted
Posted

I have actually just done this sort of thing in my car.

I basically used the existing carpet as a template to cut the mdf. I stuck 2 seperate pieces with liquid nails onto the corners/sides to act as like a fixed mount. Then I built a hinged 'lid' to allow access to the spare tyre and fixed the hinges to the corners pieces. It seems to work pretty well and once carpeted looks pretty neat.

I know that the corners pieces are now fixed, but the beauty of liquid nails is that it can be broken if needed, but is otherwise pretty sturdy. I aslo used hinges with removable pins so that the lid can also be removed. With the hinged lid setup I also have access to the spare tyre.

It was near impossible to get an exact match up with all the contours, but with the existing carpet you can get it pretty close with the timber, then wack carpet over the top and kinda free cut it so it matches up cleanly.

I chose to use mdf because it is easier to cut than ply and doesn't splinter, which is important because there are a lot of difficult curves to cut with the jigsaw...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R34 power steering

      By GTSBoy · Posted

      49719 is the cooler loop. Right at the front, LHS of that diagram. Return line from rack (LP side) goes to cooler loop on RHS front of car, then back under engine and returns to bottom of tank. 49717M is feed from tank to pump. HP line out of pump is thick rubber, followed by the hard line that runs down to crossmember and runs in parallel (but opposite flow direction) to the LP return line. Nothing goes anywhere near the firewall or interior of car. The closest they get to that is the connections on the rack.
    • drifter17a
      R34 power steering

      By drifter17a · Posted

      Thanks, plan is to drain all fluid tomorrow and do smoke test to find out the leak.   Appreciate your help and want to understand how the system work. So cooling is achieved by the long loop not any rad? The diagram seems to suggest it connects to somewhere inside the cabin and I thought that is a cooler inside firewall. If you look at the diagram it seems to show it connects to something inside firewall. I tried chasing it but not easy unless I take loads off   i am confident pump is good as fluid goes in and it gets soft( steering) but as soon as I turn engine off , loads of bubble come to surface and overflow. When engine is on , fluid level is below minimum but when off it shoots off and thinking it is sucking air in. I suspect aluminium pipe may have a crack line or whole   smoke test with no fluid should be a good start and if needed will remove the pump   In addition, the one going under the engine bay is high pressure line and one directly connecting from pump to resorvoir is return/ low pressure?   finally I searched and suggestion is to use dexron 2 but that is discontinued so bought dexron 3 as all research suggest it is compatible and shouldn’t cause any issues/ blow seals. I bought two liter of dexron 3 motul atf
    • GTSBoy
      RB25 S2 Idles but doesn't want to rev

      By GTSBoy · Posted

      Don't worry about. Just don't try to drive hard enough to make boost and you'll be fine.
    • GTSBoy
      R34 power steering

      By GTSBoy · Posted

      Yes. This has already been said. It is a loop of hardline in front of the radiator. Because.... the pump is on the LHS and the steering rack hydraulic connections are where they always are on a RHD steering rack....on the RHS. The high pressure line goes down under the engine, along the crossmember, like it does on all Skylines. Don't just throw expensive braided hoses/other kits at it. Work out what is wrong and fix that.
    • Trilbyte
      RB25 S2 Idles but doesn't want to rev

      By Trilbyte · Posted

      Still got the afm on the intake, clamps are shut tight, only loose hose is the one that goes from the j pipe towards the IACV, since it's next to impossible to find a factory hose and the barbs are different sizes (I'm still using clamps on this hose to try and help it seal on the iacv side) I've ordered parts to make up the hotside of the intercooler pipes, I'll plumb it in and see what happens in a few days I suppose The turbo's internally gated, can I just unscrew the tension rod to let the gate open?
×
×
  • Create New...