Jump to content
SAU Community

Recommended Posts

Spotted a black M35 RS (stock kit) on Ferntree Gully Rd today (near Caribbean Gardens)

Looks sh#t hot Cam. Congrats!!

You ended out getting it for a good price too. :thumbsup:

lol, thanks Jase, but that was the auction start price and certainly not what I paid for it.

Spotted a red c34 at lobathol today roughly about 3:00pm very neat and tidy and also spotted another c34 white, black rims and black spoiler on main north road at muno para dayum it looked clean cheers for the wave too ;)

Spotted Silver M35 'RX' on Mountain Highway Bayswater at 6:30pm tonight heading towards Wantirna just before Stud Road. Another one i haven't seen b4.

lol, thanks Jase, but that was the auction start price and certainly not what I paid for it.

I know that bud....I was talkin' about what you DID win it for..... :ph34r:

Silver M35 250t RX Four (YLW-xxx) in Mornington about 20mins ago.

Followed it down Nepean Hwy on my way back to work (was in a black Magna).

If anyone on here... please get larger wheels or at least larger tyres. What you have on it at the moment could fit on a Yaris FFS!

how do you manage to go to the drift on sat but never make it to stag cruises hey ? :glare:

No workies on sat :cheers:

Went wit Chris and da boyz ..hada make sure he was keeping a good name for da shop!!! :whistling: haha

Was going to have a few laps driving simos car ( dyno I sent ya ) but cracked the scotch on da drive up with a pie ..brekkie of champions haha

Then passenger all day and drinks ..couldn't say no haha plus 1st time back on track after simos tune n mods!

Getting in and out of chris's car is like being born again haha got sum good shots and good inside laps vids of chris n simo!

Gota love the back window sticker it's F N huge! :thumbsup:

Spotted a red c34 at lobathol today roughly about 3:00pm very neat and tidy and also spotted another c34 white, black rims and black spoiler on main north road at muno para dayum it looked clean cheers for the wave too ;)

Thought it was you Midnight, yours looks well clean, sweet rims :yes: . Reckon i saw the same red C34 (metallic) in Kapunda that morn. If it wasnt then they sure had a good squizz :unsure: at the rice at the servo.

Thought it was you Midnight, yours looks well clean, sweet rims :yes: . Reckon i saw the same red C34 (metallic) in Kapunda that morn. If it wasnt then they sure had a good squizz :unsure: at the rice at the servo.

Cheers Springsteen appreciated :) the red c34 had a SAU sticker on the side from memory and looked like 34 gtr rims but possibly a knock off of them?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
×
×
  • Create New...