Jump to content
SAU Community

Recommended Posts

Dont know if anyone can help, but supposing you had 18x10in wheels on the rear and 18x8in wheels on the front of your R33 GTST, would it be illegal?

From the RTA website I believe you can increase the width and diameter by 1in over standard.

My question is, is the standard taken from the model, or series etc? ie is the standard taken from the largest factory wheel size for skylines in general or just GTSTs?

I think Skyline GTRs came with 17x9in from the factory does that cover skyline GTSTs as well?

Im thinking it would be specific to each series of skyline, can anyone confirm this?

Thanks!

Link to comment
https://www.sau.com.au/forums/topic/53580-wheel-legalities-in-nsw/
Share on other sites

but I'm pretty sure there is no rule in NSW regarding rim height. You can go 1" wider than what it says on your tyre placard...and skylines have different placards depending on the scheme they were imported under and even different companies that complied them

you are right duncan you can have 20" rims if you like as long as the wheel tyre diameter combo is the same as stock ( they allow about 3% either way i think ) .

as for the width you can only widen the wheels by 1" but the track can only be 1" wider , but who is going to check the track width ?

nah its much easier for the cops.....they just see big wheels and go "bingo! Youve got a defect" See they don't have to be right, they just need "suspicion" that something is wrong....in fact I've even heard of cases where they have been shown the engineers certificate saying it is legal but still defecting the car anyway....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Is the 650rpm idle on the rb25det neo for stock cars only? I've never had my car before and after tuning it to idle at 650rpm when cold. Always idle's cold around 1100rpm, and then drops to about 900-950rpm. I've heard the r33 gtst's idle there. 
    • Series 1 RB25DET 5 speed gearbox, push type, 1st and 2nd gear syncros worn, may need bearings. Comes with quick shift, Tomei gear knob, release fork, bearing carrier, master and slave cylinder. $850. Cusco Super Single clutch,assembly, 225mm, used, comes with a Direct Clutch solid centre 5 puck ceramic clutch plate. $290. RB26 cams used, excellent condition. $280. HDI GT2 intercooler, excellent condition, has 3 inch piping welded to inlet and outlet. $250. All items located in South Eastern Melbourne. Please PM me if interested.
    • Hi all, I’m currently running a str pipe hi low hks exhaust and downpipe. Was wondering if I change out muffler to a titanium one will it change the sound of the exhaust? Plus I have always liked the look of the titanium pipes … anyone have recommendations to one?    side note already have titanium intake pipes. 
    • I looked up my other car that is a R33 GTST series 1.5. Anyone able to confirm what a Aero Form Bumper is?     (1G) 2 Door Coupe; (2GK + 11V) RB25DET; (4B) 2WD HICAS; (7F) 5 Speed Manual; (14G) Super Fine Hard Coat; (15U) Large Rear Spoiler + Aero Form Bumper + Rear Wiper (Aero Selection)
    • Ha ha, all good! I've almost caved in and realised I'm buying one.  I know myself well enough by now that I will start chasing ADHD butterflies half way through building it and not finish it so I'm better off spending the extra money buying one instead of making one just so I can get into straight away.  I would very much enjoy making one as fabrication is probably a strength and definitely a passion but I don't want that to be at the detriment to the car I'm ultimately building it for! There's some pretty good ones around for ~$1100 at the moment so I think I'll just go that way.  At the end I sell it or as mentioned, get another project to make further use of it! Thanks gents.  
×
×
  • Create New...