Jump to content
SAU Community

Recommended Posts

Nissan OEM part for t28 flange which I'm assuming will fit my t518z and aftermarket dump (as they should both be same as the original as they are bolt-ons).

Nissan have said $41 new cos I've heard the aftermarket ones are crap.

Can anyone beat $41 or suggest an aftermarket one that will be good?

This is in preparation for fitting a new stainless exhaust manifold so I figure may as well change over a gasket (or put one on) while I'm there :)

You are right about the aftermarket ones being crap, but if your genuine one isn't busted, i'd reuse it. They last ages.

I bet you will find all sorts of nuts and bolts missing when putting the manifold on....

Too_much - yeah i'd like to re-use it but I don't wanna have everything apart then find out it ain't there or ain't in a condition to be put back on so I will buy one and think of it as an upgrade. If the old one is good that's cool I'll sell mine on or keep it spare - I'm sure someone will need it.

VLS_BACK - Thanks - please let me know I will be ordering soon.

meggala - S15?! which part is s15? the dump pipe ?

PS. is there a way I can check what condition it's in before I start taking stuff off ? I'm assuming no-way.

Well if advan's one is half price I'll pay the postage and get that. Mind you $10 postage = $30.. $40 for a nissan one.. HMM

well. truth be told i will pay the lowest price for the good that works. if it doesn't work ill pay more till i get the cheapest one that will.. .. i just dont like overpaying.. and $40 for a freakin boot seems exxy.

Guess I'll have to get it then..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Quite right, if you make it to that pension you deserve every cent
    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
×
×
  • Create New...