Jump to content
SAU Community

The Wasteland - ACT Style


krzysiu

Recommended Posts

120605355.png

thats what i got on speedtest

Im assuming its the torrent because the max speed that another peer is downloading at is 10-15kB/s...

Just downloaded a 37MB and was downloading at 130+KB/s... is that alright?

Edited by SKYLVIA
Link to comment
Share on other sites

haha you are such a newbie beau 130+kb's is shit for the plan you are on plus your latency is quiet high you must be a fair ways from the exchange. Do what i say and go to the microsoft website and download something you will be gauranteed that there bandwidth will be greater than yours.

Link to comment
Share on other sites

I dunno.. I heard 2 nerd arguing whether or not the image file extention '.gif', was pronounced 'Gif', as in "Gift" or, 'Gif', as in "Mr Jiffy".

I think it got to an extent where fists were raised.

Link to comment
Share on other sites

your on crack

P.S. i checked Line configuration on bigpond site, there were 2 options, standard or fast

Difference between them was:

Standard -

Noise Margin: 6dB

Interleaving: ON

Fast -

Noise Margin: 6dB

Interleaving: OFF

It said Fast could incure dropouts etc... but would be faster data transfer or something... i guess ill see what happens?

Edited by SKYLVIA
Link to comment
Share on other sites

This should settle it :blink:

"CompuServe used to distribute a graphics display program called CompuShow. In the documentation for version 8.33 in the FAQ section, it states:

The GIF (Graphics Interchange Format), pronounced "JIF", was designed by CompuServe and the official specification released in June of 1987. "

Google delivers.

Link to comment
Share on other sites

Gif as in Gift for sure!!! I dont care what google says :P

sif you'd say Jif... it's a G not a J!!!

do you go around saying Jolf instead of Golf or Jiggle instead of Giggle or Jet the f**k out instead of Get the f**k out... should I keep going??

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Greetings to you all, It's an honour to be part of the great forum. I’m happy to learn and build good  relationships with members of this community. Thanks for having me!    
    • normally i don't like to get involed with these kinds of self promotions stuff, but good on you for living your dream man.
    • Remember our cars are 30+ years old so expect the rubber bits to leak. I'd go around your engine bay with a can of "start ya bastard" or similar and look for leaks. FYI I got my car 10+ years ago with the standard boost restrictor in place, I removed it when I got it and the car never had any issues since (besices a leaking manifold gasket). tl;dr- Look for leaks before proceeding.
    • That SSR is actually the same (or similar) as the Jaycar 100AMP SSR (which I use). They suggest the resistor to stop the SSR turning on when the ECU turns off (I believe). I personally don't use the resistor as I use the 5V output from the ECU to supply power to the SSR. I do however run a flyback diode, the old Haltech documentation was wrong too and didn't specify the fly back, I mentioned it to a few of their staff and they eventually added it in.
    • I did manage to do this without removing the engine or front cross member, but I had the advantage that the exhaust manifold was removed. I am not setup to support the engine from the top or remove it. 1. Loosen the engine mount nuts so they only have a nut of thread. If it is a manual, I think you have to remove the gearbox to engine support brackets. 2. Jack up the engine off the bottom idler mount. Jack it up till the end of the slot and nut on the mount. You need this clearance to get the pan out at the rear of the engine. 3.Break the sealant seal to sump. I found a oil pan separator tool helpful to get it started. 4. The oil pick up can be removed with the gap available.  5. The oil pan can be removed now. 6. Before assembling, do not apply sealant to the oil pick up area as your hand will rub it all off but apply to the other three and a bit sides. 7. It is a two man job to put the oil pan back, with the sealant, as you do not want it to touch anything and rub off. 8. With one person supporting the oil pan the other can fit the oil pickup 9. Apply the remaining sealant. This would be more difficult with the manifold or turbo in place, but I think it could be done. As you can see my sealant is a bit ugly, but good enough to seal. 10. Lift the sump up to the engine and bolt it on. We found it was easier to use two long guide bolts at each end to get it nice and aligned without touching.
×
×
  • Create New...