Jump to content
SAU Community

Recommended Posts

phone LCD screen replacements

anyone know who/where does this and can be trusted ?

I have 2 HTC Mobile phones where I have cracked the screen

These are worth $450 and $650 bucks so I'd like to see if I can repair them

all help appreciated :)

I've done it before on HTC depends which model it is I can probably do it for you. Sometimes you have to get the LCD plus the digitizer because it's nearly impossible to seperate them.

You can try the phone shop vendors in tuggers mall or Woden infront of Vodafone

Soda blasting was used on my GTR bonnet. Very gently but still managed to rip a whole in the alloy bonnet.

I think in the hands of an experienced operator it has it's benefits.

I expect rubber and sills need to be covered correctly or avoided.

Ive always done my cars prep by hand. The whole lot. Takes a long time but you get better results. Hope damage was not too bad Mik.

The rubbers can be fixed, they are old and hard and can be sanded back, maybe thats why the soda did that.

The plastic bit in the back window seal is fked anyway, i might cut it out and do a bead of sealant in the gap.

So in hindsight, you can sand just as close or closer than you can blast, and blasting lifts the rubber and leaves crud under there.

Im glad i only did a couple of spots, ill have to clean behind the rubber to get it sitting flush again.

post-89755-0-06799200-1392885986_thumb.jpg

Its good for getting paint out of the tight corners, and probly good for cleaning small metal parts

Its not working properly, the guy sent a bag of the wrong soda, so it clogs up. It works with constant shaking, but thats kinda hard to do while your trying to use it.

I cant get blasting soda in canberra that i know of, and the car will be primed before the right stuff turns up....... :/

Maybe ill do the old wheels or something.

Caught up with a few mates and went for a quick cruise - they met up with the Braddon guys... left there not wanting to be around kidz doing fatty skiddiez. So went up to Mt Ansilie and chatted about Initial D with a m8 who tagged along then went home. So good taking Rosie out for a long nip :)

Spotted a R33 GTR and a white R34 GTT and about 50 SS's haha

Edited by RosieR34

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • 49719 is the cooler loop. Right at the front, LHS of that diagram. Return line from rack (LP side) goes to cooler loop on RHS front of car, then back under engine and returns to bottom of tank. 49717M is feed from tank to pump. HP line out of pump is thick rubber, followed by the hard line that runs down to crossmember and runs in parallel (but opposite flow direction) to the LP return line. Nothing goes anywhere near the firewall or interior of car. The closest they get to that is the connections on the rack.
    • Thanks, plan is to drain all fluid tomorrow and do smoke test to find out the leak.   Appreciate your help and want to understand how the system work. So cooling is achieved by the long loop not any rad? The diagram seems to suggest it connects to somewhere inside the cabin and I thought that is a cooler inside firewall. If you look at the diagram it seems to show it connects to something inside firewall. I tried chasing it but not easy unless I take loads off   i am confident pump is good as fluid goes in and it gets soft( steering) but as soon as I turn engine off , loads of bubble come to surface and overflow. When engine is on , fluid level is below minimum but when off it shoots off and thinking it is sucking air in. I suspect aluminium pipe may have a crack line or whole   smoke test with no fluid should be a good start and if needed will remove the pump   In addition, the one going under the engine bay is high pressure line and one directly connecting from pump to resorvoir is return/ low pressure?   finally I searched and suggestion is to use dexron 2 but that is discontinued so bought dexron 3 as all research suggest it is compatible and shouldn’t cause any issues/ blow seals. I bought two liter of dexron 3 motul atf
    • Don't worry about. Just don't try to drive hard enough to make boost and you'll be fine.
    • Yes. This has already been said. It is a loop of hardline in front of the radiator. Because.... the pump is on the LHS and the steering rack hydraulic connections are where they always are on a RHD steering rack....on the RHS. The high pressure line goes down under the engine, along the crossmember, like it does on all Skylines. Don't just throw expensive braided hoses/other kits at it. Work out what is wrong and fix that.
    • Still got the afm on the intake, clamps are shut tight, only loose hose is the one that goes from the j pipe towards the IACV, since it's next to impossible to find a factory hose and the barbs are different sizes (I'm still using clamps on this hose to try and help it seal on the iacv side) I've ordered parts to make up the hotside of the intercooler pipes, I'll plumb it in and see what happens in a few days I suppose The turbo's internally gated, can I just unscrew the tension rod to let the gate open?
×
×
  • Create New...