Jump to content
SAU Community

Recommended Posts

on pennant hills road today, bout an hour ago.

spotted alot of sponsored cars

list as follows

whiteline evo7

blue s15 with fmic covered with vinyls

2x mini coopers

VK grp A

Maloo ute and porche, both silver with a pink stripe

and a couple classic cars

also saw the donut king r32 GTR on homebush bay drive

all had numbers on the side

this was all within 30mins

is there some sort of event on????

Link to comment
https://www.sau.com.au/forums/topic/54637-is-there-a-track-or-rally-event-on/
Share on other sites

http://www.news.com.au/common/story_page/0...55E1702,00.html

Rally driver dies during race

October 29, 2004

A SEASONED rally driver was killed and his navigator seriously injured in a high-speed crash during the East Coast Targa Rally west of Sydney today.

The driver of a Porsche competing in the event died after he went into cardiac arrest as a result of injuries from the rollover.

The accident happened on a stretch of sealed road between Brewongle and Loxley, east of Bathurst, about 10am (AEST).

Inspector Chris Davey from Bathurst police said the vehicle lost control after passing over a narrow bridge before veering to the left and crashing into a deep creek bed.

"It veered off to the left side of the road and crashed into a ditch, landing on its roof," Insp Davey said.

Medical personnel were able to free the men, both from Victoria.

"Both occupants were released from the vehicle and unfortunately the driver of the vehicle died on scene," Insp Davey said.

The passenger was treated at the scene for suspected spinal, neck and abdominal injuries.

He was airlifted to Nepean Hospital in a serious but stable condition, a spokeswoman for the Confederation of Australian Motor Sport (CAMS) said.

Insp Davey said the circumstances of the accident were being investigated and a report would be made to the coroner.

CAMS would conduct an investigation, he said.

Police and rally organisers today would not name the driver but rally director Tony Pennell said he was highly experienced and had competed in many Australian rallies.

Rally organisers stopped competition for that section of the event after the accident but continued competition for the following stages.

"Extensive rally safety procedures were implemented as a result of the incident," Mr Pennell said in a statement.

"No other competitors were at risk during the incident."

Competition will continue on the final day of the rally tomorrow.

The four-day rally is held on 198km of sealed public roads which are closed for the event.

The rally, first held in 2000, is conducted over at least 37 stages on roads in areas to the north and west of Sydney, extending into the Blue Mountains and around the towns of Lithgow, Bathurst, Oberon and Orange.

AAP

................................................................................

.............................................

:D :D :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Gday   on the hunt for an rb25 gearbox and clutch to go into my R32 rb25/30 build happy to travel a bit or pay for freight for the right one From my limited research, think I need an rb25 driveshaft yoke to make it fit so I’m after one of those too located Bathurst
    • Common for single gauges to be swapped around. My 33 GTST when I bought it had a GTR tacho fitted, everything else was GTST gauges.
    • Google says for a 1998 Nissan Maxima to pull/pry, and the metal pin might even come out with it. I'd do a bit more googling, there was a few videos, find some where the shafts/needles appear most similar and compare the techniques.
    • Details: Turbo Borg Warner EFR 9180 with 1.05 rear housing Upgraded TurboSmart integrated BOV Sanded and powdercoated compressor cover in gloss black Elbow welded with wiggins clamp Speed Sensor(Not included) (Can include oil drain(heat wrapped + titanium intake pipe with almost new filter for a tad extra). Manifold: 6 Boost RB26/30 twin scroll manifold  e-MAP ports drilled into both scrolls(I was using the TAARKS EMAP KIT) Turbo is in excellent condition. Always used Penrite 15w50 Racing oil(Changed less then 2000ks). Also using the Turbosmart OP regulator and filter. Downpipe: 4inch Stainless steel with VBand inlet and outlet clamps(included) Heat wrapped Dual ports for Dyno/Wideband usage Will throw in free 2.5 inch intercooler pipe(2.5inch From turbo outlet to 3.5 inch intercooler) - Powder coated black. Turbo made 563rwkw on mainline hub dyno at around 24-25psi boost - Pump fuel. Will def make over 600kw on e85. Didn't bother as my e-MAP was through the roof with my setup sitting past the choke line. I have a cnc ported and fully built head on my 3.2. Turbine speed saw max of around 109k rpm. I'm running this on my R32 GTR, with AC, and the original power steering pump. The manifold clears the AC lines, ABS, and everything else. Although I had new AC lines because I just wanted new ones and I heat wrapped them as well. This will make more power on a slightly lower capacity motor with a higher PR. And I have since upgraded to a G45-1500. Have pics and videos if need be.  Absolutely nothing wrong with setup. Turbo is in perfect condition. No shaft play or oil leaks at all. All the work was professionally done. The transient response of this is fkn amazing. I cannot rave more about this turbo. If I wasn't chasing 4 figures, I would have kept it. $5000 NZ. Located: Auckland, New Zealand.    
    • I particularly like the look of the John Player Special team. (Thumbnail isn't different but hit play for the clip)  
×
×
  • Create New...