Jump to content
SAU Community

Recommended Posts

hey,

Today my car started making a ticking sound (loud, very audioable when driving) from the turbo side of the engine. It happen when on gas, fast, slow whenever i am on the gas i hear the sound, also if i put the foot down and go up into the rev range it sounds like its getting faster. It doesnt do it on idle, thou if i rev it it sounds to only make it around the 3/4000 rpm mark (the same spot my bov starts going off)

Now with all this in mind, on monday, my Oil line from my turbo to engine blow (was rubber not metal -- dont ask me) now i lost 4L of oil, my mech replace the line with a stock metal rb line, refill with oil and the car was given the OK that everything was working

Now from my limited knownage, i think it might be the turbo, its boosting fine and making power but it sounds like the ticking is related to the spinning of the turbo wheel (guess?)

I will have the car check out on monday (or maybe 2morrow), But if i cant get it in 2morrow it will wreak my head in untill monday can anyone help

thanks mike :D

Hey

I've had the same problem with my car. Does you car have a full exhaust system? This normally happens when you have a cat-back exhaust. You build too much pressure and you blow out one of the gaskets. So as you rev higher you can hear it louder as it is leaking more air. Try getting an exhaust specialist out. Are you in sydney? Give me a yell if you are! Got someone that can help!

Phil

Yeah most likely its gonna be the one of the gaskets. I've blown one before and in the verge of blowing another one. Just get your car checked out by an exhaust specialist. It should cost around $300 mark. If you know the guy you might get it cheaper!

If it was the turbo it would be a very fast noise, almost a buzzing but if it is a ticking and you lost that much oil I'm considering a big end bearing. Get it checked fast and don't drive it unless you have to. The bearing and journal can sieze causing a conrod to snap which will destroy your engine.

Sorry if it sounds over the top but it isn't worth destroying an engine. I had one in mine and the ticking/tapping noise was quite loud in the garage and seemed louder on the left side.

Drop the oil and look for golden coloured metal specs and flakes. If they are there a bearing is going. In that case a rebuild is needed, probably with a crank and conrod big end grind. Sorry to say will be expensive if it is but you get to rebuild a decent engine that will last ages.

I hope it is not that bad but from what you say, it seems pretty clear.

michael ,

it sounds like a big end sorry to say mate .

do this little test . when the engine is cold ( stone cold ) start it up and listen for the noise, it should be very mild while the engine is cold ( thick oil takes up the slac on the bearing ) .

when the engine and oil gets to normal operating temp the noise will get louder , if thats the case then its a big end .

michael ,

it sounds like a big end sorry to say mate .

do this little test . when the engine is cold ( stone cold ) start it up and listen for the noise,  it should be very mild while the engine is cold ( thick oil takes up the slac on the bearing ) .

when the engine and oil gets to normal operating temp the noise will get louder , if thats the case then its a big end .

ok i just did that test, the sound is louder when the car is cold, when the car comes to normal oil/rpm/temp it becomes very quite and u can bearly hear it. give the car a few revs and it comes back for a few seconds :s

i am very confused

exhaust leak, most probably the manifold bolts/studs loose or broken or about to break.

tighten the bolts up, but there is a fair chance that some might break so take care.

Apparently this is a common flaw with the rb engines - dodgy exhaust manifold bolts!

exhaust leak, most probably the manifold bolts/studs loose or broken or about to break.

tighten the bolts up, but there is a fair chance that some might break so take care.

The botls snap.. I had EXACTLY the same thing happen to me at wakefield park. Turns out my exhaust manifold had a slight warp in it and had snapped 6 of the bolts. Its very common on skylines

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Howdy friends, So another weird one today, I was looking into replacing some broken clips holding the front grille for the R32 GTR (part number 01553-03831), and noticed the brackets which are supposed to hold the grille in place were also missing 馃槕. I do recall seeing this issue many years ago, but didn't fix it at the time. A quick look on eBay and I was able to find the genuine brackets, along with all the screws which suited the headlights (part numbers 26042-08U05,26092-08U05). Happy days!....  Once they arrived however there was an extra nut in the packaging which implied that there should also be a bolt or a stud, and sure enough, after a bit of searching I found this thread from 2013, and @Ants clearly shows a stud should be present. Reading around a bit more, it's possible the headlights on my car are the "povo pack" headlights as mentioned by @funkymonkey in this thread way back in 2008. This could explain why the studs are missing on my set of headlights. Looking at the headlight diagram I wasn't able to see a suitable part number for the stud itself. The headlight did indeed have a recess that looked like it would accept a stud, but interestingly no thread or anything obvious how the stud would be affixed to the headlight, I suspect it may have been glued in, press fit, or melted into the plastic at the factory. Another member may be able to clarify if they happen to have a genuine set of N1 headlamps. The only thing we have to work with within the recess is a keyway which likely is there to prevent the stud from rotating within the recess. In any case, back to 3D printing, I put together a model which acts like a pug with a friction fit inside this recess, making use of the keyway so it doesn't rotate while tightening a bolt. Printing in TPU will allow it to slightly swell making a nice snug fit without cracking the part. I've designed the adaptor it to accept an 20 mm M6 bolt (stainless with a cap head in my case), as opposed to the standard M5 stud and I made use of the standard galvanised split washer that came with the genuine brackets from Nissan. Once the bolt and screws were all in place, giving the bracket a gentle shake gave the classic "shaking the car" feeling, very solid, which gives me confidence this is going to be able to hold on much better than the janky solution which seems to have been here for the past decade or so. Overall I'm really pleased with how this turned out and maybe there are more people out there running these headlights without a centre stud at all! Link to the freely available model on Printables: Click here Regards, Sean  
    • Hey everyone, This is my first post apart of the introduction. I tried searching a bit on the forum but couldn't really get a straight answer. I got the car to my mechanic as I felt it being weak. It seems that it was missing on two cylinders due to the injectors. I had all my injectors clean and the car runs much better. The mechanic also confirmed my suspicions that the cat is clogged and needs to be tackled asap. The cat rattles a bit and the hot exhaust warning frequently lights up when driving after getting the injectors clean. In my introduction I was asked about what modification I might be interested in and mentioned a cat delete. From what I was told, this is not really beneficial on the RB20DE and there are more cons than pros.  Could perhaps anyone give some suggestions on what the best course of action would be since the current cat is toast and needs to be removed/replaced anyway? I can also sometimes smell a strong smell of fuel, but I'm not sure if this is related.
    • Hope the cans went down well at least 
    • 255 can't go wrong with the price.
    • When I was replacing my pump due to being stranded in the wrong state, I went with the Deatschwerks 320lph kit. It is a direct plug in to the stock wires, harness, everything. It comes with a plug... but you can plug the OEM plug directly into this thing. https://justjap.com/products/deatschwerks-dw300-fuel-pump-nissan-s13-silvia-r32-r33-r34-skyline-c34-stagea?currency=AUD Downside: Won't actually flow that much on boost if you want to push it on E85, but it's comparable to the 040/255 etc. Little more actually.
  • Create New...