Jump to content
SAU Community

Water in Catch Can

SLY SKY

By SLY SKY,
in General Automotive Discussion

 Share

Recommended Posts

JCMarshall_Law Proficient

JCMarshall_Law

Posted
Posted

That sounds very bad, cracked head could leak coolant into the cam cover, from there it could end up in the catch can.

Ther is another posibility, which may be a little less worrying. The reaction of petrol (mostly octane) produces carbon dioxide and water vapour. You could be getting blow by (CO2 and water vapour) and the water vapour could be consensing in the catch can. I would have thought that it would have boiled off again (and ended up being scavanged throught the intake if you have the scavanging system operating).

It is hard to tell which is more likely without seeing the car, I'd need to know:

1) did you find the water when the engine was cold or hot.

2) did you find it right after the engine was running or had tha car sat around for a while.

3) how much did you find

4) could you tell if it was coolant or plain water.

5) is there way the water could have leaked in (is it a atmo vented catch can)

It will probably become obvious if it is a cracked head before long so lets hope thats not it. Blow-by is no big deal, even new engines have it, just gets worse over the life of an engine from wear, eventually could require a rebuild.

JCMarshall_Law Proficient

JCMarshall_Law

Posted
Posted

I don't see how a blown head gasket could leak coolant into the cam cover.

SLY SKY: open up the cam cover (or even just the oil filler cap) and have a look around,

can you see water? (lets hope not),

can you smell water? (got a strange musty smell usually)

is the oil milky at all (maybe drain the oil and check).

Get back to us and tell us how it went.

SLY SKY Contributor

SLY SKY

Posted
  • Author
Posted

It builds up say after 2>3 weeks, its clear not green. About a cup full.

My water level is always the same, at oil changes everything looks good if a blown head gasket the water in the radiator should drop. I thought it might be condensation. I don't know. :alcoholic

SLY SKY Contributor

SLY SKY

Posted
  • Author
Posted
I don't see how a blown head gasket could leak coolant into the cam cover.

SLY SKY: open up the cam cover (or even just the oil filler cap) and have a look around,  

can you see water? (lets hope not),  

can you smell water? (got a strange musty smell usually)  

is the oil milky at all (maybe drain the oil and check).

Get back to us and tell us how it went.

Clean as looks normal, oil fine. :burnout:

SLY SKY Contributor

SLY SKY

Posted
  • Author
Posted
Its only condensation mate. Totally normal during the winter months. From the responses you've received thus far I'd take it the other guys aren't running a catch can.

Sleep well tonight.

Thanks dude, youre right it has only started doing it in the last few months. :thankyou:

rockabilly Rising Star

rockabilly

Posted
Posted

hi mate, my 33gtr has a cusco tank on it and it fills twice a year about a pint. done this for the last few years. never loose,s water no oil contamination. if you do short bursts and it damp weather the engine will absorb moisture from the atmosphere as it cools. normalyy [without a catch tank] it is sucted into the turbo and burned, but this lowers the air density in the chamber hence less power, catch tank takes the moisture away from the turbo.just empty it and carry on as usual. hope this helps..............bernie/uk.

  • 2 weeks later...
sparktat Apprentice

sparktat

Posted
Posted

"EMPTY THE CATCH CAN"! I didn't know you had to empty it as i did an oil change the other week and i didn't even give it a thought. Mine is a GREDDY can, (side mounted) is it just a matter of disconnecting hoses and tipping upside down, or do you have to take it apart?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Duncan
      NC MX5

      By Duncan · Posted

      Quite right, if you make it to that pension you deserve every cent
    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • MBS206
      RB20DE NEO smallbox clutch.

      By MBS206 · Posted

      From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • MBS206
      Lock up the old for sale / wtb threads.

      By MBS206 · Posted

      That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
×
×
  • Create New...