Jump to content
SAU Community

Recommended Posts

My car is fairly standard yet making good power.

MODS:

3" zorst

FMIC (HKS, strange item, both inlet and outlet on same end tank)

Cold air induction + HKS pod

Some sort of chip, as it flies past the rev-limiter and has way too nice of an AFR curve.

standard turbo running around .9-1.0 bar

207.8rwkw with a 13.5@108mph

sorry about dyno size but

edit: peak power is at 7400rpm

GTR Intercooler

HKS Super-dragger, Hi-Flo Cat, HPC coated dump pipe

rb20 wastegate actuator, bleed valve combo for 12psi

stock turbo

iridium sparkies gapped to .8mm

98 RON BP Ultimate

ex cam gear 4 degrees retard

hks pod with cold air partition

Power FC

210RWKW in Shootout Mode - and pulls like a train on boost !!

Picture_14_.JPG

hey guys im new here but thought i might share my powers too.

4dr r33 pumped 251.1 rwkw @ 15psi power run only

power fc

xtr gtst upgrade turbo (pretty suprised how efficient they are)

bosch 600hp pump

highflowed injectors

nismo reg

3'zorst

more tuning needed (expecting 265-270 on same boost and around 280-290 on 18psi although dont know if its wise)

Apexi RX6 550HP Turbo

Apexi Rb25 Forged bottom end kit.

Apexi 260 Degree Cams

Wolf3D Management

393hp@ 14psi

418hp@ 18psi

Boost comes on at 3000 RPM

15psi @ 4200 RPM

18psi @ 4500 RPM

Just tested it last week at Kwinana Motorplex 11.75 @ 122 MPH

Can post up the graph tonight

I'm still trying to sort out some tuning issues but I saw 234 rwkw from my car a couple of days ago.

GCG highflow

CES split dump

Fujitsubo 3" cat back with 2 mufflers for quietness

panel filter in stock air box

480cc Nismo injectors

ROM tune from Powerplay (still to be sorted)

About 12-13 psi at peak power (also have boost controller issues)

just thaught ide add to stock turbo r33 gtsts making over 200rwkw. because i think people need to realize its not as uncommon or amazing as alot of people think.

3in turbo back exaust, high flow cat

std turb 11psi

pod with cai

ex cam gear -3deg

hks type s fmic

std ecu+ safc 2

208.8rwkw and done a 13.4 on its first run at wsid

bottom end rebuild

forged pistons

tomei 256º cams

EBC @ 10psi

SAFC

full 3.5" (stock dump)

stock cooler (Hybrid kit waiting to go on)

stock turbo

NOT in shootout mode 166rwkw

as an example I got 178rwkw before the rebuild with a tired motor, in SO mode

93 R33 GTST

stock turbo @ 12psi

stock ECU, injectors, fuel pump

3" turbo back exhaust w/ cat pipe

Pod with partition and CAI

Hybrid copy FMIC with backyard piping :rofl:

SAFC2

200.9 rwkw

Well I'm still not entirely happy with things and now my transmission is crapping itself.

Anyway here are the dyno sheets.

Mods.

Stock airbox with Nismo panel filter

GCG highflow turbo

CES split dump/front pipe

3" cat

3" Fujitsubo cat back with 2 mufflers

480cc Nismo injectors

Auto - chipped ECU

R34 GTR fuel pump

R34 GTR regulator

around 12psi boost.

My next setup,

engine with less compression

t88-33d @ 1.6bar

custom manifold

hi flowed injectors

msd ignition

microtech

forward facing standard plenum

cooler

bosch fuel pump and reg

The first dyno sheet is in non shoot out mode,

the second is in shoot out mode on 1.3bar and a cracked exhaust manifold.

GTT at Stage1 (exhaust etc)

Trust TD05-18g

14psi

Standard ECU

98RON fuel

Figure is HP at the wheelhubs on a Dynapak

r34dynohp.jpg

Same car with same turbo but FMIC/Inj/Pump/ECU etc

TD05-18g

17.5psi

PowerFC

98 RON fuel

Figure is HP at the wheelhubs on a Dynapak

r34dynomar04bhp.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It only looks tidy, as most of the stuff that was on the whole back wall, is now in the trailer to go to the tip, or has been shoved in my 2.2x2.4m "Spare parts room", and now I can't get to anything in there Ha ha ha I could definitely do with a bit more space, but I'd just end up with your problems I'm going to enclose the car port beside the garage, and move a lot of stuff into it I think. OR... It will be setup as a fabrication area, and the main garage will have parts storage in it. I'm not sure yet... Need some pictures of that big shed you've got with the bikes and Skyline in
    • No. I think it's gone. 😭 I think you can get body coloured ones on eBay so I think I'll get one of those... Or just hang a red ribbon from the hole and whack a TOW sticker next to it.
    • Can't say I've had a bad experience with one on my car, then again it only gets washed once or twice a year... The wheels on the other hand, get a good spray often due to my shitty dusty pads.
    • @MBS206 thats pretty neat and tidy to me!  I'll get a photo of mine when I'm out there next. It might require multiple photos to understand the scale of the atrocities though... In total I have 4 sheds of varying sizes and layouts. Main shed is 14x8, second shed is 3x8, third shed is 11x2.5, fourth shed is around 6x4.  All are pretty much full.   The main goal of my cleaning tsunami is to make the main shed predominantly car and motorbikes only. Second shed is my metal fab room (2 x bench grinders, drill press, bench belt sander, metal band saw, scrap metal storage and some of my garden tools.  3rd shed is more bigger garden stuff, storage for engine crane, jack stands, concrete grinder, concrete mixer, air compressor lives there, and it now has two 2mx2m pallet racking shelves with itemised boxes holding building stuff, electrical stuff, plumbing stuff, etc, etc.  The 4th shed is Ryobi electric ride on mower, mini boom sprayer, ancient Kubota tractor, more garden stuff!  I have got a lot of shit....  Then there's the pool house (8mx4m) and the pool pump shed (4mx4m).  I built all of the sheds over the 11 years we've been here.  The main shed was a Ranbuild kit, the rest are all custom made to fit the areas available. Building the main shed taught me a LOT as I had no idea about building anything prior to that!  I've still got one more in me. It will be my man cave which I poured the extra concrete for way back when I poured the concrete for the main shed. The idea is the Skyline will be a centre piece of the main cave once (if...) it's finished.  I told my now 14 year old son yesterday that I will 100% drive him to his year 10 formal in 2 years. Still a long way off but at least I now have a date to work towards! 🤣
    • Modern oils are amazing. Add tyres to that as well.
×
×
  • Create New...