Jump to content
SAU Community

Recommended Posts

I have never seen it, BUT the S15 fronts are not a simple bolt on addition to the S13's so therefore, don't expect them to go on without modification onto cefiro or laurel.

However with the kits available for S13's i would not imagine it would be too difficult. Would look a bit screwed up in my opinion though.

Link to comment
https://www.sau.com.au/forums/topic/56130-ichigo-cefiro/#findComment-1089402
Share on other sites

haha well its got some skyline bits, and its got some s13 bits... and maybe more :) *oooh the suspense*

i wouldn't say bolted... lol you should check out some of the conversion jobs, shit like held on by an aluminium bracket that you can bend by hand n stuff. Then there's the bog jobs... thems real fun.

Link to comment
https://www.sau.com.au/forums/topic/56130-ichigo-cefiro/#findComment-1089427
Share on other sites

However with the kits available for S13's i would not imagine it would be too difficult. Would look a bit screwed up in my opinion though.

Actually the kits for the S13 and RPS13 isnt that difficult.

Ive seen the kit for it and its easy to put together... i was going to get one for my mates RPS13 for 1800 including the lights, flared guards and vertex bar.

Link to comment
https://www.sau.com.au/forums/topic/56130-ichigo-cefiro/#findComment-1089546
Share on other sites

isn't she purrrdy? we found her in the scrap parts section of yahoo auctions, checked the VIN, it was a 1989, only problem was that the engine was siezed, so we organised it to be trucked to the port and loaded. couldn't make up some ramps coz it was too low n stuff so had to send the mechanic out to mess with it.

Interior is clean as, with custom gauge install (not usual caveman style drill holes everywhere and poke shit in) in the centre console etc.

cost next to nothing cos it was a part taking car :)

Link to comment
https://www.sau.com.au/forums/topic/56130-ichigo-cefiro/#findComment-1089950
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Adjusting the idle screw is usually (emphasis on usually) just covering up deeper issues. Stuff like the cold start valve not closing properly. Throttle shaft seals on the way out. Coolant temp sensors getting out of spec. Coolant temp sensors especially can be a bear to diagnose because they can fail subtly. My dad just spent weeks chasing down his high idle. He cleaned the coolant temp sensor and everything but the resistance curve just drifts over time and if it's been 20+ years they also get super slow to respond as well. Has a massive effect on fuel economy as if it's off the ECU is going to run richer and command high idle for far longer than it should otherwise.
    • How old is the battery, it's more likely your battery is on its way out.
    • I reckon you'd get 90% off. My washer doesn't get between spokes very well. Haha! I love my Gerni!  Argh! Steam cleaning has its place for sure.
    • Hey all, I did a voltage test with the car (video attached) not running for 3 days. And here is some interesting stuff: - Battery voltage is 12v (I had the key in the ON position) - Drops to 9.76v while cranking then quickly goes up to 14.5v - You will notice there was a sorta slow start but not as slow as it usually is. - Idle surprisingly was better at just over 1,000rpm instead of 1,100 rpm. - I turned on the A/C, radio and headlights in the video and the voltage remains the same - I haven't cleaned the grounding wires on the chassis yet, that's next. - Battery drops to 12.6v when I turn off the car and wait a bit Seems like I might have a parasitic draw? I do have an immobiliser system which does drain the battery more of course but was wondering if there is anything else I should be looking at fixing? Does the ground wires on the chassis have anything to do with the low 12v?        SAU.avi
    • My lord that is some low oil pressure as minimum in the manual! I guess the big part will be seeing how it changes as the engine gets more spirited use.
×
×
  • Create New...