Jump to content
SAU Community

Recommended Posts

Hi guys and gals

I was just wondering, when i start up my car and leave it ideling then pump the brake pedal a few times the revs go down and almost stalls.

It never stalls but it feels like it is just about to.

Is this normal or is there something wrong?

If something is wrong would anyone know what it is?

The whole car is still under warrenty, so i want to sort it out.

Thanx

Adam

Link to comment
https://www.sau.com.au/forums/topic/5621-brake-pedal/
Share on other sites

I believe the brakes use manifold vacuum to operate the vacuum servo unit, this is the big round black thing behind your mastercylinder that helps you put pressure into it. Repeatedly pumping the brake pedal on a cold engine would be like pulling off a vacuum line and would stuff around with the engine management. RB engines that have an issue with "idle hunt" are usually first inspected for vacuum leaks. Do the revs drop when you pull the vehicle up to a stop while driving?

Link to comment
https://www.sau.com.au/forums/topic/5621-brake-pedal/#findComment-85070
Share on other sites

If the brakes feel ok and you don't have to stomp on them hard to pull up the vehicle then the vacuum servo unit may not be defective/leaking. I just went out, started my r32 and pumped the pedal 3 times and the rev's dropped significantly but then returned to normal. Is there a reason you are depressing the pedal in succesion? I don't think there is anything wrong with your vehicle adam but if in doubt consult a professional mechanic.

Hope this helped

Rhys

Link to comment
https://www.sau.com.au/forums/topic/5621-brake-pedal/#findComment-85731
Share on other sites

skylark, your on the money about the brake using vacuum thing.

Problem has to be vacuum related. It can be real hard to locate very small leaks in the system tho.

as lark said, is there a reason you pump the brake pedal?? Or you might just be fussy like me and think "i should be able to pump the brake pedal whenever i like, and not have any problems, this is a SKYLINE!!"

:P :P :D :D

Link to comment
https://www.sau.com.au/forums/topic/5621-brake-pedal/#findComment-85743
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This is the clearest explanation out of those: Page 77: Turn the crankshaft clockwise two full rotations with the tensioner pulley installation bolt in a loose condition. Insert a wrench into the tensioner pulley hexagonal hole to fix the tensioner pulley in place, then tighten the installation bolts. Tightening torque: 43–58 N·m (4.4–5.9 kg·m). The timing belt tension should be at the correct tension. Basically you turn the engine with the tensioner bolt loose, then use the allen key to hold it while you torque it up. And yes after that a good guide is being able to twist it 90o in one of the long free lengths of the belt
    • good choice....I have a set of those and use them all the time including on this job. Plus, no-one wants a damaged nipple
    • Thanks all, went with nismo strengthened belt and all genuine nissan idler and tensioner Question on RB25DET Neo Timing Tensioner: I have a question about the RB25DET Neo timing tensioner. In one of the videos (minute 20 of https://www.youtube.com/watch?v=17y37BB9xnA and minute 27 of https://www.youtube.com/watch?v=Pb99s2E9xUg), the process suggests tightening the tensioner pulley installation bolt to the specified torque initially, and then loosening it slightly to allow the spring to set the correct tension. Is this the correct approach? The R33 workshop manual on page 74 states: Loosen the tension pulley installation nuts. Insert the wrench into the tensioner pulley hexagonal hole and turn it clockwise to tighten the installation nut temporarily. The way this is written is confusing. Does this mean: Undo the nut, then reduce the tension by turning clockwise? Snug the nut so it stays in position without applying tension to the belt while removing the timing belt? The manual wording makes it sound like the nut will tighten automatically when you turn the tensioner clockwise , which is unclear to me.   Timing Belt Tension Adjustment Process: After loosening the tensioner nut, you turn the engine two full rotations by hand, which should set the correct tension. Once the tension is set, you tighten the bolt to 43 N·m (4.4 kg·m). Before tightening, you need to insert the Allen key into the hexagonal hole to hold the pulley in place while tightening the bolt. In one of the videos, it’s mentioned that you should twist the belt side to side, or turn it slightly to check if the tension is correct. The belt should turn halfway, indicating the right tension. However, I know that twisting or turning the belt is not a good idea. What are your thoughts on this? Finally, how can I ensure the belt isn’t overtightened? I’ve seen many cases where people have overtightened the timing belt.   Manual Excerpts: Page 74: Loosen the tension pulley installation nuts. Insert the wrench into the tensioner pulley hexagonal hole and turn it clockwise to tighten the installation nut temporarily. Remove the timing belt from each pulley. Page 77: Turn the crankshaft clockwise two full rotations with the tensioner pulley installation bolt in a loose condition. Insert a wrench into the tensioner pulley hexagonal hole to fix the tensioner pulley in place, then tighten the installation bolts. Tightening torque: 43–58 N·m (4.4–5.9 kg·m). The timing belt tension should be at the correct tension.
    • Takes a few minutes to malke one. Wood, or steel, or a wrap strap with some strategically placed solids to provide teh drive onto the ribs.
×
×
  • Create New...