Jump to content
SAU Community

Clutch master cylinder movement

Bl4cK32
 Share

Recommended Posts

Bl4cK32 Grand Master

Bl4cK32

Posted
Posted

Ive got a r33 gb in my r32, with an os giken twin plate / flywheel behind the rb31det.

I had some drama with the clutch this morning (found out it ran dry of hydraulic clutch fluid?? :))

Anyway, i got someone to pump the clutch after i filled the little clutch reservior up with fluid. Now i know the os twin is a heavy clutch, but the firewall had a HEAP of movement from depressing the clutch!!

Is there a clutch mastercylinder stopper, similar to the brake master clyinder stopper (like the cusco one pictured below)?

what can i do to help stop the huge movement the firewall has when i use the clutch??

:)

Link to comment
https://www.sau.com.au/forums/topic/56340-clutch-master-cylinder-movement/
Share on other sites
Bl4cK32 Grand Master

Bl4cK32

Posted
  • Author
Posted

Im an ADR welder...lol...spose its about time i made something for the car, rather than just buying a jap bolt on solution....:)

Im suprised no one else has seen this before? Or is it just me? ....i remember a mate had an old LJ Torana that used to snap the linkage up under the firewall...had it welded up and strengthened....

Hmmm.....Anyone be interested in buying one of these if i make some up :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      🚨 Need Advice! Overcharged for Engineering Report 🚨

      By MBS206 · Posted

      Well, in 2007 he must have been charging about $1800 an hour. He only looked at the car for 5 minutes. And another 4 to write the report wrong, and another minute to correct it. Mind you, this was for a car that was: Stock engine, fmic (hole in drivers guard), all alloy intake and custom air box, 3 inch turbo back exhaust, lowered, and a set of 17" Advans (255/40/17 rear and 235/45/17 front). It was nothing crazy. The blue slipper wanted the "hole in the guard" engineered. But that was because he got the shits that I wouldn't "relocate the battery from the boot, back to the factory position in the engine bay"... In an R33 GTST...     Also for emissions, E85, and don't go wild on timing. It's amazing how the closer you get ignition timing towards max torque, the last couple of degrees really throw NOx counts right up. And for the huge increase in emissions, it's only a small increase in torque.
    • MBS206
      Neil's R33 Gts-t Build

      By MBS206 · Posted

      He'll be looking down and swearing about "the damn apprentice" for trying to convince Duncan to use percussive maintenance... 😛  
    • GTSBoy
      WTB noltec r32 front upper (camber) arms

      By GTSBoy · Posted

      I swear at my GKTech ones every time I have to take them apart and replace a spherical. But I wouldn't swap them for anything else. They absolutely slay every other option, at least in terms of how they actually work. You sure you don't want to live with bearings? I mean, they don't have "ball bearings". They are rod ends and sphericals throughout. Tough as nuts, even though I have found more than one way to wear them out.
    • The Bogan
      🚨 Need Advice! Overcharged for Engineering Report 🚨

      By The Bogan · Posted

      From when I was looking at getting the 86 engineered for the turbo, the joint said to put in a few euro 5 or 6 cats, then tune the car on a nice clean E85 tune When I was looking at a turbo for the MX5, it was basically the same thing, a couple of cats and a nice clean tune Although, it will depend on the year of the Jeep IRT emmisions standards required, and what mods are done, especially if it has a newer engine installed that requires a higher Euro
    • GTSBoy
      🚨 Need Advice! Overcharged for Engineering Report 🚨

      By GTSBoy · Posted

      Yeah - but it's not actually that easy. There are limits for HC, CO, NOx and particulates. Particulates shouldn't be a concern in any petrol engine unless trying to comply to the very latest Euro standard. But getting a tune right so that all the others stay within limits AT THE SAME TIME is not a trivial exercise. You couldn't possibly get it right by just guessing at the tuner's dyno, unless he had a 4 gas analyser up the pipe, which is not often the case these days. It used to be. Every decent shop that did "tune ups" (as opposed to tuning) would have a 4 gas analsyer. Perhaps there's still quite a few of them around these days. But most "tuners" are only watching O2 and power readings.
×
×
  • Create New...