Jump to content
SAU Community

Recommended Posts

Howdy All,

Just a bit of info for all fellow Stagea type people. And that is that the fuel pumps on the RS4's aren't the same setup as the ones on the R33's.

I went to change mine today, undid the big black plastic locating ring, pulled the cap up and there was only the fuel gauge sender hanging off of it !!! The pump is mounted to the right/bottom side of the fuel tank. Not like the R33's were the pump is mounted to the big cap thingy :)

Soooo, I could be wrong here, but I would say that we'd have to go external if we want to upgrade the fuel pumps, as getting to the factory one down the bottom of the fuel tank is gunna be close to impossible :(

J

P.S. - Anybody want to buy a Walbro internal for $150 + postage :kick:

Link to comment
https://www.sau.com.au/forums/topic/57066-stagea-fuel-pump/
Share on other sites

Interesting.... And the reason I say that is in the Nismo catalogue the 260RS pump is listed as the same as the BNR32 (not BNCR33). Is the tank different, or????

I was considering the R32 pump in my car as a first choice, but it seems that matters may be slightly complicated.

Link to comment
https://www.sau.com.au/forums/topic/57066-stagea-fuel-pump/#findComment-1103389
Share on other sites

You have to be able to get to the pump to service it. There must be a way. As for the Stagea tank being the same as the R32 tank, my Stagea tank is molded plastic and the R32 tank is fabricated steel.:cheers:

Link to comment
https://www.sau.com.au/forums/topic/57066-stagea-fuel-pump/#findComment-1103854
Share on other sites

Ahh, very good.

Was it difficult getting the factory mount/bracket out ? When I had the big cap off, it looked pretty damn hard to get to the mount/pump to get it out.

I was going to take a photo of it but I was a bit worried about using the flash around the petrol.. lol

J

Link to comment
https://www.sau.com.au/forums/topic/57066-stagea-fuel-pump/#findComment-1106193
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The Frenchy's kit is the way to go forward. A modern compressor that weighs about 1/2 as much, is at least twice as efficient, and will do a good job on R134a. And of course the kit has everything else you need to connect it up and have it work properly.
    • Hey all , I am in the process of having the AC system in my r32 GTST converted from r12 to r134a and I’m being told my compressor has gone bad and I will need a new one. I was wondering if anybody has any suggestions for what is the best route to go aside from dropping $1500 on a new oem one? I did see that Frenchy’s performance garage offers a kit to mount a Toyota compressor, has anybody actually used this kit on their car? Or is there anywhere I could purchase just a clutch? Any help is appreciated.
    • Well, your RB20 ECU loom won't have wires for the boost solenoid, that boost sensor, and possibly one or two other things. There could be differences in seemingly random things like the charcoal canister purge solenoid, because the 25DET has to handle boost in the vacuum system and the 20DE does not. I don't know - I haven't looked. It is very likely that all the most important things are same-same, being the main sensors like AFM, CAS, etc, and the injectors and ignition. Not that you'll need the AFM for the Haltech anyway. I would suggest that you would seriously want to sit down with the pinouts for both ECUs and just go through them and highlight green what is the same, orange what is different/missing, and make a plan from there. It's not going to be difficult. It will either be the same or need to be fixed.
    • yeaaa that's why I haven't done any wiring to the stock ecu harness because I have the haltech, but then that leads me to the other question of "is the pnp harness really plug and play?" or would I have to still switch some pins/wires over because the pnp is for the rb25det neo harness, and not for the rb20de neo harness. was really hoping to find something to spoon feed me since so many people have done rb20neo + t conversions, but man this is rough.
    • Temu raptor, lol. At least the owner isn't your typical ranger danger lot
×
×
  • Create New...