Jump to content
SAU Community

Recommended Posts

  • Replies 69
  • Created
  • Last Reply

Top Posters In This Topic

hi guys

sorry I haven't replied to you all for a couple of days. Just doing this group buy stuff is taking up all my time. :P OK I have to keep it short cause I have more organising. I know for sure on the weekend I can get 6~10 short shift kits. I Will buy them all up front cause I know there is more than 15 definite buyers. I will also talk to him about were the other short shift kits are. I may have to go to one of the people he sold 1000 to and get it off him or there should be some on the plane. I will do my best to satify all you hungry beasts :(

ok that it for me at the moment. Oh if you still want the kit still let me know Im still taking orders but can't guarente more people at this stage.

I will contact everyone on saturday I have pms/email/sms to sort out aarrggghh. I need a ful day to sort this stuff out... seriously.

I have picked up 3 short shift kit and they have been purchased by some of hte people in this forum. I have another 3 comming tomorrow maybe day after - supplier just has to dig them up 2 of them also have already been purchased. I will notify one lucky person who has already confirmed to take the kit. My supplier is still chasing up for more short shift kits the guy who is getting the kits from is a disorganised %^$%^#$. I will keep post up something on this forum when I hear something.

I can't take anymore buyers in this group buy... I'm having trouble enough trying to feed everyone :)

For those of you that want a short shift kit there will be another group buy when another shipment comes in. Maybe between 1 - 2 months time.

sure will.

Since I have been stuffed around BIG TIME!!!! My supplier has promised to sell them to me for $120. So next time round I will notifiy you all who missed out this time and make sure you get one.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...