Jump to content
SAU Community

Recommended Posts

PICS ARE UP!!

http://www.carsales.com.au/pls/carsales/!q...ype=0&ad_type=1

I have a brand new 400R bodykit for R33 GTST, includes

front bar, side skirts and rear bar $700

Two different styles of 400R front bars, difference is in the side air vents and the bottom of centre

3 have been SOLD and 1 is left = $250

I have a Explosive half rear bar which connects straight on top of the stock bar. Brand New, raw, ready to be primed and painted. $200 with the m spec rear bar (Looks very similar to 400R rear bar)

http://www.jetspeed.com.au/showModel.php?id=1297

If sold this week will drop price !!

Pick up in sydney preferred but will send interstate at buyers expense

Mob: 0414 096 594

Link to comment
https://www.sau.com.au/forums/topic/57649-r33-bodykit/
Share on other sites

is the kit all brand new?

or has it been used before?

what sorta quality is the fibreglass?

and about the 400R front bar.... does it come with the mesh + indicators, or just plain and does it require prepariton or is it ready to be primer coated.

Answer all questions plz, im sure other ppl would be glad to know this info as well.

ahh yeh, how many of them have you got? or are u trading with them.

thanx

cheers.

Link to comment
https://www.sau.com.au/forums/topic/57649-r33-bodykit/#findComment-1111069
Share on other sites

Compared to many other kits i've seen on the the market, this one is much thicker and better quality, it's brand new never used, ready to be primed and painted

Link to comment
https://www.sau.com.au/forums/topic/57649-r33-bodykit/#findComment-1111189
Share on other sites

Three 400R front bars have been sold, Two pairs of 400R skirts have been sold, Rear bar has been sold, One 400R front bar is left = $250 and Explosive half bar with m spec rear bar = $200

Link to comment
https://www.sau.com.au/forums/topic/57649-r33-bodykit/#findComment-1113389
Share on other sites

Its not missing mate, this is the new design, the old design of the dark grey shown in the photo only has that part in the middle, also the side air vents are different

hey mate with the pic of the blue front bar, the bar across the front is missing, making the gap bigger, why is that?

do u have one with it still on there?

Link to comment
https://www.sau.com.au/forums/topic/57649-r33-bodykit/#findComment-1113452
Share on other sites

yeh, it looks good but there will be a gap under the were the front mount sits, as in most cases i have seen fron mount finish along that middle part.

will u be able to get those pics by tonight? side and front angles would be nice?

cheers mate

Link to comment
https://www.sau.com.au/forums/topic/57649-r33-bodykit/#findComment-1113672
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
×
×
  • Create New...