Jump to content
SAU Community

FS: Volk/Rays TE37

j-plus
 Share

Recommended Posts

j-plus Enthusiast

j-plus

Posted
Posted

FS: Volk/Rays TE37 in bronze (5 x 114.3)

F: 18 x 8.5 (+30)

R: 18 x 9.5 (+35)

Wheels are in good condition, but not in the same excellent condition as the Work Meister S1's and the GT2's...

Also come with a full set of Volk/Rays wheel nuts (in black to match the stickers!)

l2ite372.th.jpg

More pics tonight....

Once again, the best price around - happy to send interstate

$2,100

Kind Regards,

Jeff.

Link to comment
https://www.sau.com.au/forums/topic/57807-fs-volkrays-te37/
Share on other sites
Guest two.06l

Guest two.06l

Posted
Posted
FS: Volk/Rays TE37 in bronze (5 x 114.3)

F: 18 x 8.5 (+30)

R: 18 x 9.5 (+35)

Wheels are in good condition, but not in the same excellent condition as the Work Meister S1's and the GT2's...

Also come with a full set of Volk/Rays wheel nuts (in black to match the stickers!)

l2ite372.th.jpg

More pics tonight....

Once again, the best price around - happy to send interstate

$2,340

Kind Regards,

Jeff.

Would you consider selling the nuts? if so how much?

Link to comment
https://www.sau.com.au/forums/topic/57807-fs-volkrays-te37/#findComment-1112558
Share on other sites
j-plus Enthusiast

j-plus

Posted
  • Author
Posted

Seems to be a lot of interest in GTR fitments - wait until February!

Anyway, more pics showing the condition of the wheels...

j7rvolks.th.jpg

l5pte371.th.jpg

The worst example of gutter damage:

i9dte373.th.jpg

Paint damage evident on one wheel. There is no structural damage whatsoever, it appears as though (maybe battery acid, thinners???) has splashed and eaten into the paint. No amount of polishing will remove it! However, the surface is smooth to the touch:

a1ete374.th.jpg

Up close:

w2qte375.th.jpg

Hott interest in these - keep it coming...

Link to comment
https://www.sau.com.au/forums/topic/57807-fs-volkrays-te37/#findComment-1112718
Share on other sites
j-plus Enthusiast

j-plus

Posted
  • Author
Posted

I have fitted these to an R33 Gtst without issue.

The fronts fit perfectly, plenty of caliper clearance (Brembo’s would fit easily) whilst remaining inside the guards.

The rears are a tighter fit, coming close to the suspension on the inside and sitting just inside the guards – but still fit. Over big bumps and/or extreme lowering (as per your previous cars!) they could hit, I can’t be sure. However, rolling the rear guards would be a necessity, as would stretched rubber.

Now, if an R32 is the same/very similar in this area as an R33, you will be ok. Whether they are the same is another question…

Trial fitting is welcome (however, I know you are in Perth)...

Link to comment
https://www.sau.com.au/forums/topic/57807-fs-volkrays-te37/#findComment-1129616
Share on other sites
  • 2 months later...
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By TurboTapin · Posted

      Do the following first and get back to us. - Clean and verify your IACV - Verify for vacuum leaks/post MAF leaks. (Pressure test is the best and cheapest way) - Do you have a BOV with stock ecu/MAF? If so, remove it.     
    • DRoc81
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By DRoc81 · Posted

      Hey all, The skyline I have is stalling when the engine is at normal operating temp.  When starting it while it is cold, it'll run just fine.  I have replaced the battery (bad cell), I have replaced the fuel pump, fuel filter and clean the MAF sensor.  Any other suggestions?
    • DRoc81
      Shifting questions

      By DRoc81 · Posted

      Thanks for all the information on this.  I tried ordering the parts from Amayama website and all 3 Solenoids are discontinued and not available.  Does anyone have any other websites to suggest that I could find the parts?   Separate issue-- I will start a new thread, but basically the vehicle is stalling when warmed up.
    • TurboTapin
      RB25DET Solid lifter conversion

      By TurboTapin · Posted

      It's unfortunate what Tomei USA has done to Tomei's name in general. I'm very weary of ordering parts from them now. I only order direct from a Japanse source (e.g Nengun). At least their logos are different, so you end up knowing what you have. 
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Update Issues 5 (plus #4) - 10 After making a claim about issue #4's missing part, DeAgostini Japan sent a whole new issue #4 and it arrived about 2 weeks after that. That was back in early March. It took another 4 weeks to receive issues 5 - 13 though. This update is for issues 5 - 10. Ove the 5 issues the front left suspension and most of the engine have been completed. The quality of the castings and fit of the parts is quite good, it seems better than DeAgostini's BNR34 Skyline GT-R from the Fast & Furious 2 movie, which (to me anyway) doesn't seem to have as tight tolerances or quite as accurate castings.  Each issue has a lot of info about the 1989 - 1993 Skyline range and other Nissan models from that era, but the focus is on the BNR32 Skyline GT-R Nismo and the various racing it did in Japan, Europe (Spa 24hrs) and of course Australia. I've included some text translated with Google Lens in some photos and will add to them if there's anything worth including. 
×
×
  • Create New...