Jump to content
SAU Community

Recommended Posts

Its the leak yes, It happed to me before...

What it is that, where steering arm located it has Plasric/rubber cover is torn at the top.

It possibley make some kind of winding noise if you try to turn the steering wheel.

check your fluid tank and the rubber.plastic sleeve cover on steering arm.

even resiviour is full if there is leak on the top of the steering arm sleeve.

if your power steering resiviour bubble when car is stationary or not(turning). means there is leak some where.... ( my guess would be those one of steering arm rubber/plastic covers.

Run your fingers over them (squizze them) to check for leaks.

also if mechanic is the only option can someone make a recomendation?

Hey, i have the same problem, just yesterday the HICAS sign decieded to pop up, in the past all i had to do was top up the fluid! but not time time :) mine doesnt make any sound thou !! fluid is fine doesnt bubble so im hopeing its just a leak?? should put it up on the ramps go have a look!

I noticed this grinding noise the other day whilst parking my R32 gts.. under the fluid resivouir i notice there's alot of dirty fluid where it looks as its been leaking (i've been topping it up).. i'm putting the car on the hoist tommorow to check the suspension anyway, so while i'm there i'm going to drain the ps fluid and check all the hoses

even resiviour is full if there is leak on the top of the steering arm sleeve.

 

if your power steering resiviour bubble when car is stationary or not(turning). means there is leak some where.... ( my guess would be those one of steering arm rubber/plastic covers.

 

Run your fingers over them (squizze them) to check for leaks.

The sleeve which is called a rack boot does not seal the fluid.

The rack seal stops fluid coming out of the housing. If there is any fluid inside that boot then the seal is broken. The boot only stops dirt from getting inside to where the seal is.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Give it 40psi and send it to the moon
    • I suspect 550s are on the large side for happy operation with a stock/Nistune RB20 ECU. The Hitachi ECU doesn't love short pulse width operation, and the RB20 doesn't need much fuel at idle. Big injectors can be unpleasant. This could be contributing.
    • Yeah, I still don't know why the idle speed control can't catch the falling RPMs. In the Consult logs I see the AAC duty cycle rising, but suddenly it goes lean and the engine stalls. Anyways, the relevance here is the DW 550cc injectors are probably the same. So if OP has similar issues I would be tempted to finger those injectors as problematic for whatever reason vs the ECU failing for some reason.
    • Yeah, sort of blurring two different things together, aren't we? I just meant O2 feedback closed loop. I used to have a 0-1V LCD meter on my dash, wired directly to the O2 sensor signal. So you could easily see what it was doing. Normal running it would flick back and forth nicely. Slow down to an idle and it would keep flicking, as the ECU tried to servo to maintain stoich, but it would slow down as each swing happened until it would stay at one end of the scale. As I said above, the sensor heater is not enough to keep it hot enough when there is also little heat in the exhaust flow. Give it a blip and it would start swinging again, then peter out again. Meanwhile, idle speed control would run just fine, because unrelated.
    • It's not even O2 feedback, it's just simply when the ECU sees the closed TPS signal for whatever reason the idle will start steadily dropping until the engine dies. With the TPS adjusted to not trigger closed TPS it will idle at some ridiculously high RPM and something like 6 degrees of timing. In the absence of getting eyes on it personally and a lot of quality time doing diagnostics I couldn't tell you what the real problem was but it was interesting nonetheless
×
×
  • Create New...