Jump to content
SAU Community

Recommended Posts

My car has just started to make a loud clicking sound from the steering column when i turn it left and right.. the steering wheels seems to be very tight with no play it is at all.

Does anyone have any idea what this could be? im starting to get worried about it....

thanks

Link to comment
https://www.sau.com.au/forums/topic/58489-loud-click-from-steering-column/
Share on other sites

Is it a four wheel drive? and does it get louder when you turn full lock and accelerate?

If not then see if it does it louder when you are parked and turn the wheel from full left to full right and back again. Does it sound like it is coming from inside the car or outside moreso?

If it's inside then it could be the column itself or the switching mechanism for the indicator. (Have you recently changed a steering wheel or something?)

If it outside the car then check the column coupling where it joins into the rack.

Also check the HICAS sensor under the steering wheel.

its and R33 GTST and it sounds like it is comming from right behind the steering wheel. i havent really noticed if it is louder stationary or in motion. I have not touched the car or steering wheel at all, but it is quite loud..

Does anyone have any idea of how to check out the steering column? it has an airbag..

See if it does it gets louder when you are parked and turn the wheel from full left to full right and back again.  

That is the worst bit of advice I have seen in a long time.....

Don't turn your wheels while the car is stationary.

It puts massive load on the power steering pump, and it's not good for your tyres either. :P

My money says it's the indicator switch making the noise. :P

That is the worst bit of advice I have seen in a long time.....

Don't turn your wheels while the car is stationary.  

It puts massive load on the power steering pump, and it's not good for your tyres either.   :thumbsup:  

My money says it's the indicator switch making the noise.  ;)

Good on ya mate.

It will only hurt the pump if you continuously do it. There is absolutely nothing wrong with doing it once or twice.

I have never seen a pump fail due to this test and it is necessary to determine its location. It also helps by putting the load on the pump as it will amplify any problem that is present. It also rules out any moving components whilst driving.

And in case you didn't notice I am offering help to people here unlike you. I already told him to check the switching device for the indicator so instead of repeating my advice and then flaming bits you know nothing about. Think before you type.

ok settle guys......hahaha that thread was funny !

anyway erhmmm

i have the same problem .

description;

clickin noise comin from outside from left hand side of car. Definelty outside the car and ft left.

only when u turn the wheel then the nosie is apparent. like a few clicks at time.

the bushes look fine ........so perhaps the column couplin ? hmm

ok settle guys......hahaha that thread was funny !

anyway erhmmm

i have the same problem .

description;

clickin noise comin from outside from left hand side of car. Definelty outside the car and ft left.

only when u turn the wheel then the nosie is apparent. like a few clicks at time.

the bushes look fine ........so perhaps the column couplin ? hmm

Is it a rapid click or just a few spaced apart. Plus is the noise only apparent when you are moving slowly or does it make when you are doing say 60 around a bend.

Has your car been lowered?

How does it handle, does it drive ok normally? (ie:do you think the noise effects the driveablility of the vehicle?)

Check bearing plates

Check spring saddle

Check steering rack mounting bushes

You should check balljoints but I would doubt these would be the problem, they would knock rather than click.

  • 1 year later...
Is it a rapid click or just a few spaced apart. Plus is the noise only apparent when you are moving slowly or does it make when you are doing say 60 around a bend.

Has your car been lowered?

How does it handle, does it drive ok normally? (ie:do you think the noise effects the driveablility of the vehicle?)

Check bearing plates

Check spring saddle

Check steering rack mounting bushes

You should check balljoints but I would doubt these would be the problem, they would knock rather than click.

noise happens when stationery and u turn the wheel.

even more loud when u are parked on a road slanting in the gutter. (hence more weight on tyre)

i think its the balljoints...if u move the front left tyre side to side while jacked up and it moves somewhat does this mean the balljoints are worn out?

please assist me in this synopsis.

only under load the clicking comes from the front left.

where and how much do the balljoints cost?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Reasonably hard, although I haven't run it with the new Endless setup yet. The old brakes were F50's on 335mm rotors and the car did a 1:40.6 at Phillip Island which is a reasonable time, I'm seeing high 600s on the temperature paint. A guy I know ran the Endless fluid at WTAC without issues and he was doing 1:33's I think (Evo) with a 355/332 setup. I don't get out to the track as much as I'd like but we put the car on the hoist and spanner check every bolt and re-paint mark everything, bleed the brakes, change the fuel, check the coolant system and re-bleed blah blah blah before every event. Motorsport is expensive, RB's are expensive so a couple of hours before an event is time well spent. It's also a net time saving because if you can keep your RB from self destructing it saves you time in the long term!
    • Welcome Alice......hope you have a bit more luck from here on! What was done in the build?  
    • Hello! I'm new here, I have an R33 GTST that is currently being finished up! Last year was pretty rough, blew two stock turbos so I decided to build the car. Has been down since November, but I get it back next weekend!
    • Hello, I believe my car was imported to America in the 2000s by Kaizo Industries. Would anyone be able to help me find more info on them? I've only found all the basic stuff like that paul walker bnr34, them being shutdown by feds, just stuff like that. Any help would be much appreciated, thanks!
    • I am using Motec M150.  I am not working on the car myself actually.  My workshop is giving all these info, they are quite reputable in the industry and are very familiar with Motec and RBs and have done a few big setups with VCam and single turbo on RBs.  In fact, they built and tuned my engine from day one.  But they are stumped with my engine at the moment and cannot work out how come the compression is so low with the VCam. They told me that they have now swapped in some Kelford cams (without the VCam) and can achieve around 130psi compression and the low end torque is better, but now the engine is doughy as.  It boosts and peaks at more than 1000rpm slower, with twin HKS GTIII RS, it doesn't get full boost until over 5000rpm. I have always thought the VCam was a bit disappointing at the low rpm. To a point I had to ride the clutch a fair bit to get up a small hill from stand still.  That was when I had a clutch.  Now changing to a 8HP, I don't have that luxury and this problem has become a major issue. I am beginning to think the VCam never work since the day it was installed.  Maybe it was just sitting at the most advanced point, that is why it went good at top end but very ordinary at the bottom.  Therefore, with the help of the Holinger 6 speed and paddle shift, as long as it was moving, it drove pretty good.
×
×
  • Create New...