Jump to content
SAU Community

rb26 into r33 gts25t

217/r33

By 217/r33,
in Engines & Forced Induction

 Share

Recommended Posts

217/r33 Community Regular

217/r33

Posted
Posted

hey guys.

I was just wondering what would be needed to do the conversion to rb26 as im looking into doing it after the new year.

- is the gear box connection the same?

- engine mounting/connection are the same as rb25?

- what will be done with the drive shafts if the rb26?

and how much would this conversion cost if i was to do it my self?

Thanks in advance :)

:)

Link to comment
https://www.sau.com.au/forums/topic/58728-rb26-into-r33-gts25t/
Share on other sites
R31Nismoid Grand Master

R31Nismoid

Posted
Posted

Doing it yourself... no more than 6k tops if you do it yourself as you say

it would be far from 10k.

Then you sell your old motor/loom you rip out

All you need is the Complete Motor with loom & ECU.

And you'll need a set of dump pipes (if you dont get em) and then just match to your existing exhaust

You could certainly get it done for less than 6k without a doubt if you sell your old motor too

Just change all the belts and stuff before you put it in.

The gearbox you have in your R33 will be fine, so driveshafts and stuff certainly dont need changing. Engine i beleive bolts up to exisiting mounts. The Joy of Nissan RB's, pretty much interchangeable

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Milkmun
      The FD RX7 is the best looking 90's JDM car

      By Milkmun · Posted

      Lucky man, who owns it in the family? Any pics? 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      The engine stuff is Greg Autism to the Max. I contacted Tony Mamo previously from AFR who went off to make his own company to further refine AFR heads. He is a wizard in US LS world. Pretty much the best person on earth who will sell you things he's done weird wizard magic to. The cam spec is not too different. I have a 232/234 .600/603 lift, 114LSA cam currently. The new one is 227/233 .638 .634. The 1.8 ratio roller rockers will effectively push this cam into the ~.670 range. These also get Mamo'ified to be drilled out and tapped to use a 10mm bolt over an 8mm for better stability. This is what lead to the cam being specced. The plan is to run it to 6800. (6600 currently). The Johnson lifters are to maintain proper lift at heavy use which is something the LS7's supposedly fail at and lose a bit of pressure, robbing you of lift at higher RPM. Hollow stem valves for better, well everything, Valve train control. I dunno. Hollow is better. The valves are also not on a standard valve angle. Compression ratio is going from 10.6 to 11.3. The cam is smaller, but also not really... The cam was specced when I generated a chart where I counted the frames of a lap video I had and noted how much of the time in % I spent at what RPM while on track at Sandown. The current cam/heads are a bit mismatched, the standard LS1 heads are the restriction to power, which is why everyone CNC's them to get a pretty solid improvement. Most of the difference between LS1->LS2->LS3 is really just better stock heads. The current cam is falling over about 600rpm earlier than it 'should' given the rest of my current setup. CNC'ing heads closes the gap with regards to heads. Aftermarket heads eliminate the gap and go further. The MMS heads go even further than that, and the heads I have in the box could quite easily be bolted to a 7.0 427ci or 454 and not be any restriction at all. Tony Mamo previously worked with AFR, designed new heads from scratch then eventually founded his own business. There he takes the AFR items and performs further wizardry, CNC'ing them and then manually porting the result. He also ports the FAST102 composite manifold: Before and after There's also an improved racing crank scraper and windage tray. Helps to keep oil in the pan. Supposedly gains 2% power. Tony also ports Melling oil pumps, so you get more oil pressure down low at idle, and the same as what you want up top thanks to a suitable relief spring. There's also the timing chain kit with a Torrington bearing to make sure the cam doesn't have any thrust. Yes I'll post a before and after when it all eventually goes together. It'll probably make 2kw more than a setup that would be $15,000 cheaper :p
    • MBS206
      Can't put strut back

      By MBS206 · Posted

      Because the cars wheels are on blocks, you slide under the car.   Pretty much all the bolts you touched should have been put in, but not fully torque up.   Back them off a turn or two, and then tighten them up from under the car with the wheels sitting on the blocks holding car up in the air.
    • MBS206
      Can't put strut back

      By MBS206 · Posted

      Yes. Imagine you have the car on the ground, and you mine away all the ground under and around it, except for the area directly under each individual wheel. That's exactly how it'd look, except the ground will be what ever you make the bit under each wheel from
    • GTSBoy
      Can't put strut back

      By GTSBoy · Posted

      Yes, if you set the "height" right so that it's basically where it would be when sitting on the wheel. It's actually exactly how I tighten bolts that need to be done that way. However....urethane bushes do NOT need to be done that way. The bush slides on both the inner and outer. It's only rubber bushes that are bonded to the outer that need to be clamped to the crush tube in the "home" position. And my car is so full of sphericals now that I have very few that I need to do properly and I sometimes forget and have to go back and fix it afterwards!
×
×
  • Create New...