Jump to content
SAU Community

Recommended Posts

Hi All, Just After Some Info On Suspension,when Buying A Set Of Say "tein" Height Adjustable Coilovers (secondhand From Japan) How Do U Know How To Check The Hardness Of The Ride They Will Give In Your Car Before Buying Them?? Bcoz Ive Heard Of Ppl Buying Them And Saying There Too Hard For Road Use, I Owuld Like To Maintain The Comfortable Ride As Much As Possible. Anyone Had Thiis Problem Or Know What Is The Best Way To Tell. Thanx 85urk.

i guess the only way to check the hardness is to whack it on the car if youve had no previous experience with coil overs. spring rates should give you an indication of how stiff the ride might be but u have to remember though different people have different definitions of "too hard" some think its too much others think its just right. a good starting point is to go for a ride with someone who has the same coilovers and springs that ur planing to buy. hope that helps

by the way, why does all ur words start with captial letters??LOL:D:D

i have just installed tein HA coilovers and i have to say i am happy with them...

the ride is harder than standard but not too bad for the road, but you do feel the bumps a bit more..the upside is the steering response and the handling has improved beyond my expectations..

i say go for them, if you dont like them you can always sell them.

I have Tein Adjustable coilovers. They are really ment for the track lol. Hard on the arse, and you feel every bump. Best handling though.

Note - stiff suspension does not a good handling car make...

common misconception amongst backyard 'tuners'. A combination of spring rates, damping, camber, castor, toe, and roll bars all together can make a car handle well.

:(

Tien HA's are pretty good. They are hard, but not as bad as some. I would suggest getting rubber boots installed to protect them from getting rooted by the aussie conditions. They really wern't designed for australia, and they will get fudged up with dust and stuff, especially if you decided to tackle a dirt road...

They aren't as hard as say HKS hyper-d coilovers, but it really depends on what you define "hard"!!

They are definantly ok for road use, ie they are not racing/track only suspenison

I have Tein Adjustable coilovers. They are really ment for the track lol. Hard on the arse, and you feel every bump. Best handling though.

True that,

Teins + Whiteline handling kit + strut brace = track setup :)

Awesome on the freeway and for tight cornering and handling but it sucks on shit roads which is pretty much everywhere :(

My car feels like a go kart, you steer it goes..

dont waste your time with teins unless you are doing track racing etc, if you are getting them just for road use see if you can get a brand of suspension that can be set soft or is soft. My teins are height/damper adj. and they are too hard. After a while of the lovely melbourne roads I soon popped both the rear shockers. Yeah on the freeway its elite but any of the other roads u feel every little crack and crevice in the road. Besides ur g/f's tits will get sore! As for JIC Magic...forget those they are mega hard. My mate had some on his r33 and with the windows down - when you drive over train tracks the window jumps about 2 inches out of the friggin door!

well that sounds painfully, im just after a comfortable ride but i dont want it crazy bouncy when you hit bumps, my mate has an s14 200sx and his suspension seems to stiff for my liking, when oyur coming down the road u can see the headlights bouncing up n down. i dont want that. also after a while of having too stiff suspension all your door cards and windows start to rattle and parts start to creak. no thanks i just want to find a happy medium that gives a smoother ride but will give better handling and cornering. only for road use too not for the track. (P.S. i dont know why all my words were in capitals weird stuff! lol)

dont waste your time with teins unless you are doing track racing etc, if you are getting them just for road use see if you can get a brand of suspension that can be set soft or is soft. My teins are height/damper adj. and they are too hard. After a while of the lovely melbourne roads I soon popped both the rear shockers.  Yeah on the freeway its elite but any of the other roads u feel every little crack and crevice in the road. Besides ur g/f's tits will get sore! As for JIC Magic...forget those they are mega hard. My mate had some on his r33 and with the windows down - when you drive over train tracks the window jumps about 2 inches out of the friggin door!

hahaha :) My girlfriend used to complain of sore tits too! She use to say she'd need a sports bra just to ride in the car, I always though it was just cause she has lovely D-cup sized babylons! But maybe it was too hard... I installed some Tein HA's along with all Whiteline urethane bushes, and front and rear strut braces, and bigger rear sway bar and I thought the car was firm, but still bearable. I have to say though that I didn't do a lot of k's in the car (not a commuting car).

Richard

for those commenting on teins, especially used ones, you cant say "teins are hard" or "teins arent too bad" because there are a whole range of springs and valve rates available, and your never going to know what the original owner in japan built them for. I bought tein HA's and they were drift setup, ROCK hard. whereas ive ridden on other sets of HA's that were completely different. Theres no harm in trying them out and if you dont like them, sell them as mentioned above (as i did), because its funny that no matter how much is said about Jap coil-overs being no good for Aus roads, there is never a shortage of dudes willing to fork out the cash for a used set!!! You never know, you may like them.

for those commenting on teins, especially used ones, you cant say "teins are hard" or "teins arent too bad" because there are a whole range of springs and valve rates available, and your never going to know what the original owner in japan built them for.  I bought tein HA's and they were drift setup, ROCK hard. whereas ive ridden on other sets of HA's that were completely different.  Theres no harm in trying them out and if you dont like them, sell them as mentioned above (as i did), because its funny that no matter how much is said about Jap coil-overs being no good for Aus roads, there is never a shortage of dudes willing to fork out the cash for a used set!!!  You never know, you may like them.

The easiaest way to make an assessment of their firmness is the spring rate. If there was any logic used in the chosen shock rebound valving it will be matched to the spring rates. So if you know the spring rates, then the shock rates are pretty obvious.:rofl:

I've driven a Whiteline/bilstein setup R32.

I was very impressed with the way it handled. General balance and smoothness over bumps.

It felt almost like stock R32 suspension, I also didn't notice any body roll.

Very nice to drive.

I've driven a R33 with coil overs and wasn't impressed.

I used to own a VS V8 Commodore that had a Whiteline/Bilstein kit fitted.

It too also handled very nice but obviously not as nice as balanced as the line. :)

For street use I really don't think you can go past the whiteline setup.

My car is a 95% daily driver 5% trackday use. I'd say go Koni or bilstein from Whiteline setup, they're nice on the road firm without getting too harsh. May not be as calibre as the other stiff suspension aimed for the true track out there, but if you own only 1 car and use it the way I use mine, u'd be happy with Whiteline. I am.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As you're looking at using a Link ECU, then large injectors are not a problem. But there's not really any need to go 1000s on an RB20 unless you're planning >>600HP on E85, which would seem unlikely. There are other options for injectors. The Xspurt ones are available from a number of places and you can get them in the mid 600s and 725cc, which is probably a sensible place to be. These are all EV14 based. If you are not using the stock AFM (at all, which would be the case with a Link) then a large turbo intake pipe to suit the ATR turbos is not an obstacle, so you should use one instead of a highflow. Results will be better.
    • Hey guys,  I'm after some advice and this here is the best place to get it imo. I was a member a looong time ago under another account, with a lost email address. Its nice to jump back on and see some of the same names still giving good advice.  I mothballed my car when i moved to perth in 2013, and after getting towed across the nullabor a few times it has officially done more km's on a trailer than under its own power. Now that i have started the process of tidying up and modifying it, i see the fruit available (and the fruiterers selling the produce) is different than back in the day. hence my questions, as i used to 'know' what to get and now, i'm not so sure. Engine wise the car (92 gtst) has a walbro 255, k+n, fmic, cam gears and and turbo back 3"exhaust. Wish list is a Hypergear high flow or ATR43G1, Link G4x and some newer injectors before a tune up. My goals are modest, only low 200's power wise. i know i could achieve this with less, but i've been swapping out old for new where i can. Every cooling hose has been replaced, along with mani gaskets, WP, thermostat and radiator, fuel pump and timing belt, tensioner and idler, and i rebuilt the steering rack. Regarding the injectors, the fruiterers all seem to sell what used to be considered quite large injectors. There are a lot of options for bosch 1000cc EV14's, and i would like to know if that is a suitable choice for my build. Is modern injector design good enough to run these at the low duty cycles that i likely would be? is there a downside to running a too large injector these days? or, would there be an upside to running a smaller injector at higher duty cycle? I can see that there are smaller injectors still available, but the ones i have seen specifically marketed for RB's are pretty large (see: https://golebysparts.au/collections/fuel-rail-injector-kits/products/nissan-rb20-fuel-rail-bosch-980cc-1150cc-injectors-turbosmart-fpr800-regulator-kit), and i dont know enough about them to say one not marketed for RB's would fit or not. I have searched the forums, and amongst all the posts on older tech, I did see gtsboy recommend EV14's, but no size was mentioned... again, i'm not clear on if the smaller size bosch injectors are also EV14's as they do look similar.  also, if someone can recommend a tuner familiar with RB's in the Geelong or West Melbourne area i'd appreciate it. Thanks in advance guys. Cheers, Rowdy  
    • FWIW the depth of the groove in the rubber pad is not super essential, the blocks are rubber and squish a bit. If you are worried an angle grinder will make a deeper groove quick smart
    • I mean, if you were to move the jacking points away from the original location, that is, away from the wheels and closer to the centreline of the car, then it will be more likely to overbalance and tip off the supports. Same as we talked about before. I was talking about moving for-aft. If the sill is bent outward or inward, then the car would obviously look unstraight from the outside. Hopefully that hasn't happened either. Again, you can do comparative measurements from the chassis rails to see if there is much deflection.
    • Can you elaborate what you mean with your first sentence? I meant move as in the bulge kinda seemed like it got pulled "outward" meaning it got pulled down and to the side with the jacking rail itself, so the load bearing bulge now sits lower than usual and is not level with the sill on the other side of the jack point. Either that or the jacking rail just got pushed in a good bit.
×
×
  • Create New...