Jump to content
SAU Community

Removing rear interior trim

Black33

By Black33,
in Exterior & Interior Styling

 Share

Recommended Posts

  • 2 months later...
predator Grand Master

predator

Posted
Posted

Your answers are as useful as a priest in a brothel guys..

You'll have to remove the rear seat first, this will allow you to remove the side plastics. To remove the seat just pull up on the base and it should pop out.. And then remove the two screws on either side of the backing piece. Then you will need to push on that with your shoulders, whilst pushing up - as it is hooked in.

The side panels should then be able to be popped out, but you may have to use some force if they haven't been removed before. You are best to work along the edges, pulling each stud out in turn.

Gamatron Enthusiast

Gamatron

Posted
Posted

did it today actualy...

on my series 1, all i did was 1st unscrew the screw benind the seatbelt.

there was 3 clips going down (closes to the door) 2 along the top and 1 behing the material on the indentation.

i didnt take mine compleatly off as i didnt need to but ull have to do somthing about where the seatbealts go down behind the pannel.

its a 5 min job very easy.

hope it helps

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Ticking Sound On Idle - Rb25

      By GTSBoy · Posted

      Well, hydraulic lifters will get noisy if they are dirty/fouled in some way, and exactly how that manifests will depend on exactly what schmutz is where. There is a procedure on here somewhere for dismantling and soaking/cleaning them. Replacing them with new is about 50% of the work and about 5% of the money!
    • myrbgivesmeheadaches
      Ticking Sound On Idle - Rb25

      By myrbgivesmeheadaches · Posted

      Thanks for the reply @GTSBoy this is is a hydraulic lifter engine. Yea right i did not realise the lifters were supposed to be compressible while installed. I could push them down but i had to lean almost my while body weight on them.  I have never heard of a lifter/ lifters ticking only at hot idle and getting worse the hotter it gets. I have owned a few jdm cars with noisy lifters. This noise is slightly more subtle, it is more of a sharp gentle metalic tic than the solid and more loud tapping I've heard on lifters. I have used a metal rod, alloy tube, hose and stethoscope and could not find the source of the tick. But it appears to be loudest on the actual engine block behind the exhaust cam gear and next to the oil filter. I had mate (40 year old mechanic) go over it with me and he couldn't find it either..  Could it be a cam seal issue of some sort?  Cheers  
    • GTSBoy
      Ticking Sound On Idle - Rb25

      By GTSBoy · Posted

      This seems problematic and unlikely at the same time. Vanilla RB2Xs have hydraulic lifters. They do have "zero" clearance, but only when running with oil pressure inside them. When not running, you should be able to compress them and obtain heaps of clearance. RB26s and Neos have solid lifters. They should have ~0.3mm and ~0.5mm on the inlet and exhaust respectively. If they have zero clearance then bad things are happening. With nothing else being wrong, it would mean that the valves would be held slightly (ever so slightly) open when they are supposed to be closed and it should have all sorts of problems when running, caused by leakage in/out through the valves. Or, zero clearance can indicate severe valve seat recession. None of it is good. Have you used a piece of hose as a stethoscope to try to localise the noise?  
    • myrbgivesmeheadaches
      Ticking Sound On Idle - Rb25

      By myrbgivesmeheadaches · Posted

      Sorry for reviving an old post, but I'm having the same hot idle tick issue. Did anyone ever find out what it was?  I have checked/ replaced Injectors Coils checked Lifter clerance (is at zero) Checked Cam lobes Replaced exhaust gasket and studs Would appreciate any advice this is driving me nuts  
    • MBS206
      NC MX5

      By MBS206 · Posted

      There's a huge reason manufacturers are tuning in dead flat torque curves... Make them reliable (and more drive able)
×
×
  • Create New...