Jump to content
SAU Community

Question about cooling system and heater core

Eikon

By Eikon,
in General Maintenance

 Share

Recommended Posts

Eikon Explorer

Eikon

Posted
Posted

I have problems with my RB20det overheating.

I had a pressure test done, so it apparently is not a head gasket.

I had a new radiator installed, so that shouldn't be the issue.

I put a new thermostat in... so that should be OK.

I beleive it is the water pump that is the problem... I just don't think it is pushing any coolant through the engine... I don't think there is any flow.

The other day I was driving it to the mechanics (Will soon be doing water pump), and noticed that I was getting NO heat from the heater. Keep in mind, it's very cold here. The temp gauge began to climb high.... still no heat!

I shut it down on the side of the road and opened the hood. In freezing temp, the engine cooled down pretty quickly. Then I turned it back on and wouldn't you know.. I got heat out of the dash... but only for a few seconds, then it sort of ran out and went back to cold/mild air. Had to shut it down one more time to be sure not to get it too hot. Then turned back on, and got heat.. but only for a few seconds... then cold air again.

Is this a sign that I am not getting any flow of coolant through the engine? Does this back up my water pump guess? Is my heater core stuffed up?

I don't understand why I would get a little heat only at start-up, and then have it go away again very shortly after.

My finger's are crossed that the water pump will be the solution.

Please let me know what your thoughts are on the heater issue.

Thanks

Craved Grand Master

Craved

Posted
Posted

was your radiator getting blocked up? this could have also happened to the heater core, low flow through that core would explain the heat at first then cooling off as there is no hot water passing through it to heat the air up again!

as for overheating... usually a water pump would leak through the front when the bearings go.... it may not be the cause..

have you run a flush through the system to clean it out?

blind_elk Grand Master

blind_elk

Posted
Posted

Have you checked the thermostat is operating properly?

Have you run a diagnostic on the A/C system?

You can check for water movement by running the engine at idle (at operating temp) without the radiator cap, and then revving the engine - you should see water moving across the filler neck of the radiator.

Eikon Explorer

Eikon

Posted
  • Author
Posted
Have you checked the thermostat is operating properly?

Have you run a diagnostic on the A/C system?

You can check for water movement by running the engine at idle (at operating temp) without the radiator cap, and then revving the engine - you should see water moving across the filler neck of the radiator.

I have not done a full system flush as I am told that is very expensive to do. Though I may have been given poor info.

The thermostat is new, and has been tested to open at the correct temp.

There is no A/C. The RB20det is swapped into a US model 240sx convertible. With the droptop, I have little need for A/C.

I will try with the radiator cap to see what I can see.

I am sure that the heater core is stuffed, as the radiator was so much that it needed to be replaced. But, if it was stuffed.. why would I get even a little... I would think I would get no heat at all?

Thanks

Craved Grand Master

Craved

Posted
Posted

the heater is probably blocked but not to a point where no water goes through.

hence while it sits there it is able to heat up the core, but once the cold air is pumped through it it cools it down and the amount of water flowing through it is not enough to maintain temperature!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Ozdavroz
      New to R32 ownership

      By Ozdavroz · Posted

      Very nice - I also have a 92 GTST and hardly see any others around these days
    • xmanz
      Video Edit Programs

      By xmanz · Posted

      When I need something else to edit, I use Movavi. A friend who does video editing on a daily basis recommended me) it's an easy video cutter to use for beginners
    • Skidmore
      Video Edit Programs

      By Skidmore · Posted

      I need to edit some videos for work but I'm not good at all this. Which video editor can you recommend?
    • GTSBoy
      HY51 Fuga Hybrid

      By GTSBoy · Posted

      I think you're really missing the point. The spec is just the minimum spec that the fuel has to meet. The additive packages can, and do, go above that minimum if the fuel brand feels they need/want to. And so you get BP Ultimate or Shell Ultra (or whatever they call it) making promises to clean your engine better than the standard stuff....simply because they do actually put better additive packages in there. They do not waste special sauce on the plebian fuel if they can avoid it. I didn't say "energy density". I just said "density". That's right, the specific gravity (if you want to use a really shit old imperial description for mass per unit volume). The density being higher indicates a number of things, from reduces oxygen content, to increased numbers of double bonds or cyclic components. That then just happens to flow on to the calorific value on a volume basis being correspondingly higher. The calorific value on a mass basis barely changes, because almost all hydrocarbon materials have a very similar CV per kg. But whatever - the end result is that you do get a bit more energy per litre, which helps to offset some of the sting of the massive price bump over 91. I can go you one better than "I used to work at a fuel station". I had uni lecturers who worked at the Pt Stanvac refinery (at the time they were lecturing, as industry specialist lecturers) who were quite candid about the business. And granted, that was 30+ years ago, and you might note that I have stated above that I think the industry has since collected together near the bottom (quite like ISPs, when you think about it). Oh, did I mention that I am quite literally a combustion engineer? I'm designing (well, actually, trying to avoid designing and trying to make the junior engineer do it) a heavy fuel oil firing system for a cement plant in fricking Iraq, this week. Last week it was natural gas fired this-that. The week before it was LPG fired anode furnaces for a copper smelter (well, the burners for them, not the actual furnaces, which are just big dumb steel). I'm kinda all over fuels.
    • LjB123
      RB25 Crankshaft Differences

      By LjB123 · Posted

      Well my freshly rebuilt RB25DET Neo went bang 1000kms in, completely fried big end bearing in cylinder 1 so bad my engine seized. No knocking or oil pressure issue prior to this happening, all happened within less than a second. Had Nitto oil pump, 8L baffled sump, head drain, oil restrictors, the lot put in to prevent me spinning a bearing like i did to need the rebuild. Mechanic that looked after the works has no idea what caused it. Reckoned it may have been bearing clearance wrong in cylinder 1 we have no idea. Machinist who did the work reckoned it was something on the mechanic. Anyway thats between them, i had no part in it, just paid the money Curiosity question, does the oil system on RB’s go sump > oil pump > filter > around engine? If so, if you had a leak on an oil filter relocation plate, say sump > oil pump > filter > LEAK > around engine would this cause a low oil pressure reading if the sensors was before the filter?   TIA
×
×
  • Create New...