Jump to content
SAU Community

Recommended Posts

I have a mate who can get the avcr for $540 including postage 2 anywhere in australia.. min order is 1.. so if this deal falls through i can pm his details to those of you who are still intrested... he gets his products direct from apexi

hey player_hater can you post your mates name coz 540 door2door is pretty sweet. Very interested in that.

Please get your facts right people.. QUOTED FROM NS.COM|

"Pinoi_boi_r33: Price is $550 including door-to-door shipping, but if it gets caught up in customs, you will have to pay this. Saying that though, even if you paid the FULL Duty/GST on this, you are still paying LESS than the next lowest price on this forum - and that priced doesn't include Duty/GST wink.gif"

Who wants to pay TAX for 550$?? you will pay tax beacuse its over 400$.

My sale is 570$ NO TAX!

Cheers

Hey Doridori32

Im interested in one, can you please list your suppliers details.

Also do they own some kind of business? coz honestly I wont be depositing my money into some unknown account.

hope you can understand ppls situation and since your so new to the forum aswel

Thanks

Please get your facts right people.. QUOTED FROM NS.COM|

"Pinoi_boi_r33: Price is $550 including door-to-door shipping, but if it gets caught up in customs, you will have to pay this. Saying that though, even if you paid the FULL Duty/GST on this, you are still paying LESS than the next lowest price on this forum - and that priced doesn't include Duty/GST wink.gif"

Who wants to pay TAX for 550$?? you will pay tax beacuse its over 400$.

My sale is 570$ NO TAX!

Cheers

Hey there,

don't want to be seen as Hijacking your thread, so I'll keep this short and simple. I just thought I would reply to clear up some misconceptions spreaded by your little misleading post above :D

Yes, ours are $550, and that is all that you will pay.

Why? Because when we ship it out, the value we declare is just low enough to cover the $50 duty/gst threshold. Before you say this is illegal, I've been trading Internationally for quite a while now, and as long as I can prove that the price that I declare is higher than the price that I myself as a company get them for (i.e am still making profit), customs can say nowt about the lower price.

We are a legitimate business, and purchase over 100+ of these things a month from A'PEXi, so can get them for prices unimaginable :)

The ones that you are selling however, I highly doubt that the full duty/gst has been paid on them from whomever brought them in. I may be wrong though, and you might have purchased them from the AUS Distributor (who are, by the way, the only ones capable of offering it as this price fully duty/gst paid), but I highly doubt they would let you sell it for $570 ;)

Anyway, sorry for posting in your sales thread. Mods/Admins: If this is not acceptable, please accept my apologies and delete my post.

My group buy is reliable and is still open if anyone wants an avc-r within 2 weeks.

CLICK HERE

Ive got 5 definite buyers so far and it would still be good to get more.

Payment due by 19/01 - avc-r should be at your door by 30/12.

Price $630 delivered - if we get 5 more people $615.

OK the price isnt as good as doridori32's but the sale is actually happening.

Sorry for hijacking your thread but you know what they say aboout 'healthy competition' - besides, these group buys arent meant for the sellers benefit they are for the buyers/members of the forum.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
×
×
  • Create New...