Jump to content
SAU Community

Recommended Posts

What should an RB20DET box have printed on the side? Is it RPC71C ? Also it has #2 - there are meant to be 2 revisions in r32 so its probably right.

RP71C is RB30E gearbox

RB71C is R32 gearbox

Got both of these in the garage. Another difference is that the R32 type has a lot more ribbing on the outside surface of the bellhousing.

damn.. definitely RP71C .. although it seems to have a fair bit of ribbing along the bellhousing. It also seems to have a GTS-T shifter on it, unless that has been swapped over to make it look authentic? Which ones are the earlier red top ones? Is it possible its off an early RB20?

Can somebody post a picture of one outside the car?

damn.. definitely RP71C .. although it seems to have a fair bit of ribbing along the bellhousing.  It also seems to have a GTS-T shifter on it, unless that has been swapped over to make it look authentic? Which ones are the earlier red top ones? Is it possible its off an early RB20?

Can somebody post a picture of one outside the car?

A lot of parts are interchangeable. Here's thread on SDU that shows a picture of a GTSt gearbox plus has lots of other useful info:

http://forums.skylinesdownunder.co.nz/show...hlight=5th+gear

Hmm.. thats mostly the internals though - but thanks.

Here is a shot, if this helps. It does have a fair bit of ribbing though, like I was saying. As you can tell, its been labelled RB20 box. The guy I bought it off bought it himself as an "rb20 box" off a parts place, so i don't think he was trying to rip me off, he just didn't know himself. Either way I guess $400 for either box is a decent price, so I'm not too peeved.

I have read that the proper rb20 has different synchros, and that is the main difference? Its only fairly temporary until i have the funds for an rb25 box, so as long as it doesn't self destruct I'm hoping it should be ok for 6-12months.

From another forum - not sure whether its correct.. this is why its confusing.. lots of conflicting info out there.

RP17C is the code for the smaller 5speed gearbox from the rb20, and rb30 skylines and im pretty sure vl too

its followed by a revision number #1 or #2

the RP17C nor the revision number identify the internals of the gearbox (r32 rb20 box with twin synchro 2nds and slightly different ratios, or r31 rb30 box are all RP17C)

Here is a shot, if this helps. It does have a fair bit of ribbing though, like I was saying.  As you can tell, its been labelled RB20 box. The guy I bought it off bought it himself as an "rb20 box" off a parts place, so i don't think he was trying to rip me off, he just didn't know himself.  Either way I guess $400 for either box is a decent price, so I'm not too peeved.

Looks identical to the R32 RB20DET gb I've just done a strip and check on - but it has RB71C on the side. OTOH, an original R31 Silhouete gearbox I have has RP71C on the side, plus a few others I have seen/worked on had the same.

Anyway, that gearbox is from an RB20DET powered car AFAIC - no RB30 gearbox I've seen has that amount of ribbing on the bellhousing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Details: Turbo Borg Warner EFR 9180 with 1.05 rear housing Upgraded TurboSmart integrated BOV Sanded and powdercoated compressor cover in gloss black Elbow welded with wiggins clamp Speed Sensor(Not included) (Can include oil drain(heat wrapped + titanium intake pipe with almost new filter for a tad extra). Manifold: 6 Boost RB26/30 twin scroll manifold  e-MAP ports drilled into both scrolls(I was using the TAARKS EMAP KIT) Turbo is in excellent condition. Always used Penrite 15w50 Racing oil(Changed less then 2000ks). Also using the Turbosmart OP regulator and filter. Downpipe: 4inch Stainless steel with VBand inlet and outlet clamps(included) Heat wrapped Dual ports for Dyno/Wideband usage Will throw in free 2.5 inch intercooler pipe(2.5inch From turbo outlet to 3.5 inch intercooler) - Powder coated black. Turbo made 563rwkw on mainline hub dyno at around 24-25psi boost - Pump fuel. Will def make over 600kw on e85. Didn't bother as my e-MAP was through the roof with my setup sitting past the choke line. I have a cnc ported and fully built head on my 3.2. Turbine speed saw max of around 109k rpm. I'm running this on my R32 GTR, with AC, and the original power steering pump. The manifold clears the AC lines, ABS, and everything else. Although I had new AC lines because I just wanted new ones and I heat wrapped them as well. This will make more power on a slightly lower capacity motor with a higher PR. And I have since upgraded to a G45-1500. Have pics and videos if need be.  Absolutely nothing wrong with setup. Turbo is in perfect condition. No shaft play or oil leaks at all. All the work was professionally done. The transient response of this is fkn amazing. I cannot rave more about this turbo. If I wasn't chasing 4 figures, I would have kept it. $5000 NZ. Located: Auckland, New Zealand.    
    • I particularly like the look of the John Player Special team. (Thumbnail isn't different but hit play for the clip)  
    • Such a cool collection of cars back then.  
    • Mystery solved, thanks bro Bit of a strange mix, but i dont mind it, still looks good. 
    • nah no problems with bearings or hubs.  just the water pump leak and my AC death
×
×
  • Create New...