Jump to content
SAU Community

calipers and R33 Rotors *PICS*


Recommended Posts

Hi guys, just cleaning out the garage and got some parts i need to get rid off:

R33gtst Front Rotors. 296x30mm... Good condition, dont even need machining - they have been redrilled to fit 4stud as well as 5stud. - $$$Make me some offers

R33//R32 Rear Calipers... not 100% sure what they are... if anyone knows how to tell the difference PLEASE let me know1!! - $70

also have front set of calipers for an R32 (I THINK!!!) I bought them as R33 calipers.. but they didnt bolt up to a R32 with R33 calipers... if anyone knows how to tell PLEASE LET ME KNOW!!!! $$$Make me some offers

or whole set for $430

rotors.jpg

calipers.jpg

frontcaliper.jpg

Link to comment
Share on other sites

  • 2 weeks later...
Hi guys, just cleaning out the garage and got some parts i need to get rid off:

R33gtst Front Rotors. 296x30mm... Good condition, dont even need machining - they have been redrilled to fit 4stud as well as 5stud. - $$$Make me some offers

R33//R32 Rear Calipers... not 100% sure what they are... if anyone knows how to tell the difference PLEASE let me know1!! - $70

also have front set of calipers for an R32 (I THINK!!!) I bought them as R33 calipers.. but they didnt bolt up to a R32 with R33 calipers... if anyone knows how to tell PLEASE LET ME KNOW!!!! $$$Make me some offers

or whole set for $430

rotors.jpg  

calipers.jpg

frontcaliper.jpg

Did you sell the used 296 mm x 30 mm R33 GTST front disc rotors?

If not, how much do you want for them?

Cheers,

Richard Everett

[email protected]

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Great info @tidi0x  Will definitely be handy for others and maybe me if I decide to keep the shit box H pattern.
    • Bumping this up one last time.... I wanted to follow up on the clutch slave issue. I realized that what the issue comes down to is the pocket is flat milled, and the cylinder does not want rest flat. So in order to mount it correctly you will need to make a spacer for the fingers so the cylinder is floating. I took two plates of aluminum, drilled some holes and was good. I did still need to make the relief cuts in the bell housing, as even with the spacer the bleed section still interferes. The OE bell housing the mounting holes are raised from the housing.       
    • If the event in USA goes ahead will be interesting as it seems the rules will get more cars over here. Apparently the track is laguna seca too. Yeah s15, if I get a the lower dash trims, centre console and change front cross member to standard LCA position will fit clubsprint. See how rules are as i would rather do complete widebody than a bolt on flare to run the 295 with proper clearance.
    • If the car is legal height I can't see it being an issue. Found a thread on reddit that might offer some insight.   I got a ticket from a copper in QLD for my S15 being too low. They had this wheel thing on a stick that they put under the car and it hit my exhaust. Anyhow went to an exhaust shop to get the exhaust tucked up/hung a little higher and I wound the coilovers up a smidge. Don't think I even had to go back to the police station unlike when I got defected for having a carbon bonnet when I brought the S15 from the ACT to QLD and had to replace it and then rock up at a police station and have a yougish female officer who knew nothing about cars confirm that I had changed bonnets. Should have just painted the carbon bonnet yellow to match the rest of the car lol
    • Id like to race in the US i think alot of those track would suit me   For the s15? Youd be stuck between club sprint and the new Open Am wouldnt you depending on how much interior you have left in
×
×
  • Create New...