Jump to content
SAU Community

Recommended Posts

As some of you know my beloved V8skyline is dead........well not so much the car but the engine.

i have a dream, and that dream is to get my car into the top 10 SAU Drag times

therefore i need a very low 10 second pass,

the car will shortly be receiving a 10 pt rollcage and r33 brakes

it will have s13 coilovers and s14 hubs to enable me to fit these brakes.

i am thinking of either an rb25det or an rb26dett. i know wich one i prefer but well see how $$ goes after the other work is complete

What i want to know is 400RWKW enough for these quater miles times and what work does each engine need to have done to acheive this power....i realise the 26 needs less work to do it but it also costs more to begin with.

Link to comment
https://www.sau.com.au/forums/topic/60852-400-rwkw/
Share on other sites

i think even with the high costs of buying a rb26 your going to spend lots and lots on a 25 to get 400rwkw . a full comprehensive rebuild will be required . If you can find a rb26 in good nick (and thats going to be the problem) you should see 350-400rwkw with a pair of low mount turbos , cams and the usual bolt on mods .

Link to comment
https://www.sau.com.au/forums/topic/60852-400-rwkw/#findComment-1152456
Share on other sites

It wont be for drags, in fact i wont do a lot of racing with it at all...maybe every few months go to a street meet...and the odd bit of drift here and there(on a track of course) car WILL be a daily driver no matter how much of a pain in the a55 it is to drive....mainly cos I'm an idiot.

Only a guess but i would say that it weighs 1000-1100 kgs in full trim.

dash, front race seats and cage will be the only interior in it when complete, so it may JUST slip under the 1000 mark

Link to comment
https://www.sau.com.au/forums/topic/60852-400-rwkw/#findComment-1152800
Share on other sites

Then if you want it to daily drive the rb26dett is the best option in my opinion

As i drive a 400kwrw gtr most days

pfc & avcr apexi and hand controller

garrett 320hp ball bearing turbos

tomei 260 9.15 cams and adj wheels

700cc injectors

rb20 afms

custom exhaust and inlet

525rwhp 20psi (last 1/4 ~490hp ran 11.3 125mph)

the rest std

so that sort of power isnt hard to exact from rb26dett but i am about to change out rb20afms as there limit is about 540rwhp and am going to put forged rods and pistons just for peace of mind .Plus i'm doing some sump mods for track use.

as for a low 10 1/4 will come down to weight and setup to gain suck a time not just power

Link to comment
https://www.sau.com.au/forums/topic/60852-400-rwkw/#findComment-1153345
Share on other sites

He is saying that over a quarter mile a GT-R with 400 Kw should be doing a higher speed through the traps.

Maybe it bogged down too much at the start, or he backed off the throttle too early....

Link to comment
https://www.sau.com.au/forums/topic/60852-400-rwkw/#findComment-1153580
Share on other sites

Well when i ran it gear changes and starts were the biggest issues but even tho it's not far off wot a lot of the high 400hp cars will run in mph and please dont forget its awd not 2 wd a 2wd drive will run a slightly fast mph per hp due to weight and rotating weight .

What mph would you exspect from a 490rwhp AWD?

Link to comment
https://www.sau.com.au/forums/topic/60852-400-rwkw/#findComment-1153684
Share on other sites

very true cant agree more and the simple mph to hp only works when comparing apples with apples ie awd with awd and street tyres with street tyres my orginal post to show that its not very hard or hughly $$ to get 400rwhp from a rb26 and i simply post wot i got from my one trip to the strip

Link to comment
https://www.sau.com.au/forums/topic/60852-400-rwkw/#findComment-1153709
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


×
×
  • Create New...