Jump to content
SAU Community

TRUST/GREX oil cooler kit (suit RB25DET)

BATMBL
 Share

Recommended Posts

BATMBL Proficient

BATMBL

Posted
Posted

SOLD!

Hi guys

Im selling a used Trust/Grex oil cooler kit. It comes with Earls braided lines and fittings and all pieces(incl. adapter plate) to fit onto an RB25DET motor.

This came off an R34 GT-T, and im sure it will also fit the R33 GTS-T, as they should have the same oil filter type. It is in EXCELLENT condition and is a bolt on kit.

$650

BATMBL Proficient

BATMBL

Posted
  • Author
Posted

hi

here are the dimensions. it has 12 rows.

18.5cm High x 30cm Long x 5cm Wide.

with regards to the oil relocation kit, im not sure, to tell you honestly. the way this bolts on is very easy and quick. all you need to do is take the oil filter out, put the trust/grex plate over where the oil filter sits, use the nut it comes with and tighten it(DONT TIGHTEN IT HARD!) and put the filter back on. then just put the oil cooler at the front(has bracket), close to the water resevior, and you are done, easy.

BATMBL Proficient

BATMBL

Posted
  • Author
Posted

i couldnt say for sure, sorry Blitz_R33.

I do have a buyer for the oil cooler who will be making payment early this week. so the cooler may already be sold, pending on payment. it will be going on a R33 GTST.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By dbm7 · Posted

      Same thought crossed my mind ~ depends on how one connotes 'stalling'...ie; gets a rough/stumbling idle as it get warm until it stalls... or... idles ok and simply falls-over when it gets to temp... ...you can test the whole circuit with a couple of resistors ...unplug coolant temp sensor, bridge terminals with a 2K7 resistor (ECU will do cold start), or with engine warm bridge with a 330R resistor (ECU will consider engine to be at normal operating temp)...it's a quick way to check wiring integrity/ECU response when you don't have a multimeter handy ...
    • Murray_Calavera
      Exhaust silencers/varex exhausts

      By Murray_Calavera · Posted

      They also make them with the motor mounted on the side 
    • GTSBoy
      Blue/grey smoke after idle

      By GTSBoy · Posted

      Just be warned that that turbo will not be a direct re-fit to the car. The exhaust housing is, of course, in the same place. It has to be - it's bolted to the exhaust manifold. So the dump will fit up. But the centre housing is not as long, so the comp housing will move backwards. This will affect both the turbo inlet and the outlet. There is fab work that needs to be done. Yes. it has one, it should have one. Paper gasket.
    • PotatoCake
      Exhaust silencers/varex exhausts

      By PotatoCake · Posted

      I only recently purchased the vehicle, it came with the flex setup but the current tune is e85 only, which is why im wanting to get the tune redone to enable a mixture.  First i need to get the exhaust redone tho. I was thinking of getting a varex muffler but it sems they dont fit well in the 33 (hang low because of the valve mechanism which sticks out on top) and generally dont sound good. So that leaves me with redoing the entire exhaust (more resonators and mufflers) so its not a menace when i come and go from home, and then have the aes dump valve somewhere along the line to really open it up. I was thinking of having it before the cat but after seeing how insanely loud it will be (on a vl turbo) im thinking of putting it more towards the rear of the car, after one of the resonators. 
    • pacman_1219
      Blue/grey smoke after idle

      By pacman_1219 · Posted

      At this point I'm just 'hoping' it's the turbo seals. I did speak to someone who said it's normal for these turbos to have a bit of axial play? Not gonna lie I've never checked a turbo for axial play before but you could hear it tapping a bit as I moved it back and forth. Surely that's too much? My theory is (could be completely wrong), bad axial play, worn bearings, bad seals, oil into dump/compressor side, burns in exhaust = blue smoke. On a timing belt related note, my crank pulley was missing that front plate that sits in front of the timing belt. It's that metal round plate. It did have the rear one, and the woodruff keys are in the crank which was nice. Can anyone confirm if the NEO det engine has a front plate, im sure it would to protect the front of the timing belt or something. Water pumps...the pump I got was an NPW (yes grill me if I should've got a genuine one lol). It has a smooth mating surface, kit came with a pretty pathetic looking paper gasket. Do I need to use any RTV or just trust the gasket will work because its a smooth mating surface? Cheers legends have a good Easter break!
×
×
  • Create New...