Jump to content
SAU Community

Recommended Posts

1.) the sound it will make is not the same as the SR20 powered cars.

it is similar but not the same.

on the SR20's, that noise is caused even though they have the stock plumb back bov attached.

the return line of the S15 and S15's isn't large enough so once you increase boost a little bit, you start hearing that "DO DO DO" sound you described so well.

I can show you this in my car if you are in sydney.

The sound the skyline's make with no bov is more like a rattle snake.. like "trrrrrrrrrrr"

However, once you get a FMIC, the sound changes once again.

2.) Yes you need to block off the vacuum line as well.

a screw will do for that.

3.) Wether this damages the turbo is a whole other story.

there is no real evidence that it does or doesn't.

I know the theory of what happens with no bov all too well so no need to tell me.

Everyone has their own story/theory of what no bov will do or not do.

I don't feel the need to add mine as I have done it too many times and people obviously don't know how to search.

I'll add 2 things though.

1.) I had an ex rally car. it was a 88 Laser TX3 turbo. 1.6L

hi flow turbo.

was putting out 120kw at the front wheels when I disengaged the rears.

this thing was rallied for 50,000kms and I had it for about 20,000kms on the road.

the stock bov was removed.

it was running 1 Bar boost for the whole time, fluttering away on each gear change.

never had any turbo problems..

many others but no turbo ones.

2.) I chose to run the stock bov on my current car and even when I had my skyline for the simple reason that the car worked/works better.

it idles better, it doesn't jerk when you back off from throttle slowly..

it just runs smoother.

Even though my current S14 runs 1 bar boost and on anything above 5psi, it will flutter, normal driving on the road where you are on and off the throttle slowly rather than fast and harsh like on a track, the car behaves better.

up to you what you want.

I personally wouldn't go with no bov and my reasons are above.

if you want the "LOOK AT ME" thing, then go right ahead.

Link to comment
https://www.sau.com.au/forums/topic/62285-which-bov/page/2/#findComment-1177651
Share on other sites

  • 2 years later...

From what i understand and what others are saying its not a bov your after. Like the other guy said about taking the stock bov off and clogging the hole. This is actually bad for your turbo. That sound your askin for is compressor surge. When the throttle body closes all the boost built up has no where to go since u have no bov so it throws it back through the turbo making the chh chhhh chhhhh sound. Definately not recommend man.

Link to comment
https://www.sau.com.au/forums/topic/62285-which-bov/page/2/#findComment-3511669
Share on other sites

I personally have a HKS SSQ BOV - it makes a very nice SSHHHTTTT sound... not too loud which is wankie pankie in my opinion... bu you do need a bit of a let off sound as it' a turbo... I have an apexi power flow pod, fmic and a hks ssq - all three work in harmony and you get a SSHHHETTTTTFFF tu tu tu sound which is capped off with a fluttering sound which is tough as ... I reckon this is style... so yeah, my hats off to the HKS SSQ - if you do go for this, get that latest model as the older ones tend to affect your air flow metre and can be troublesome.

Cheers,

Link to comment
https://www.sau.com.au/forums/topic/62285-which-bov/page/2/#findComment-3511768
Share on other sites

The fine for an atmospheric BOV is

"Undue noise" $240 in QLD and 3 points

So if you get a quiet one you will be right. I had a turbo smart maximus the biggest they make on my old skyline and everytime i let off i had people on the foot path jump and other cars look and stare so i got rid of it.... HKS SSQV is the only way to go now...

yeah i use an apexi power d1 intake pod with a HKS ssq BOv n i get the nice flutter sound however i have alloy piping which helps a little, but it not to wanky.

i didn't know that was the penalty!! $240 & 3 points!!! wow :)

Link to comment
https://www.sau.com.au/forums/topic/62285-which-bov/page/2/#findComment-3512871
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • I've watched some vids and the technique seems to be to butt the sheets up to one another and use MIG to spot weld and slowly fill in the spots until its eventually all sealed. No runs as you would normally do, as there's too much heat generated that way. Yeah my stick welds are terrible these days because its been so long since i've done any of it. I expect to be spending many hours practicing
    • I have personally seen a Tomei USA RB26 cam that didn't even fit the head. Kind of nuts to me that it was even possible for that to happen but such is life.  There's two UP Garages in the US. One is a US branch of the Japanese company which sells things they brought over at tremendous markup. The other is University Place Garage/Fairlady Motors which is a shop best known for putting VCAM in RBs and trying to convince people to stop putting in 800hp of turbo on a 2.5L motor.
    • Gasless MIG is not exactly suited to what I would call "delicate" or "attractive" welding. So I would rule it out for sheet metal rust repair type stuff, unless you're only doing it in hidden places. I'm thinking about getting myself a gasless MIG for "hack together" type work. Noting that my welding experience is very very low, and quite a long time ago. So I'm also looking for "simple", but I'm not expecting "excellent". I'm not even sure that proper MIG is the best for sheet metal work. I get the feeling that the degree of control and the minimisation of heat input that you get from TIG is probably what you really want. And then you have to get good at doing it before the welds won't look like a monkey flinging a handful of shit anyway. You're probably SOL for an easy and cheap way to get from where you are to where you want to be. Much like myself.
    • Any recommendations for what would be the easiest welding type to start on, for sheet metal rust repairs and maybe some exhaust piping too? Seems like MIG is the most common. Would gasless MIG be ok to learn on and do some simple jobs? I have a stick welder which has a Lift TIG setting, but i'm more interested in getting whatever's easiest to do, and most suitable, rather than using what i have.
    • Is the UP Garage in the US of Ayyeee even the real UP Garage?
×
×
  • Create New...