Jump to content
SAU Community

Recommended Posts

Hi guys

Im contemplating throwing nos into my car cause i can get a real good deal on any HP shot (full system) OZ NOS setup?

MY rb25det, is pretty stock @ the moment (internals) other than 3" turbo back, fmic, ems, 550cc injectors, fuek pump etc...

What HP do you guys recommend, & if so, what should i have done to the motor to not fry itself...???

& I wont be using it much @ all, only on the track once or 3 times etc...

Link to comment
https://www.sau.com.au/forums/topic/62812-nos-system-wetdry-for-rb25det/
Share on other sites

Single fogger wet system, running a 50 shot I think or a 75 hahaha one or the other, be careful though the oz nos system looks like good value but when a NOS brand single fogger wet system is only $850 now with a 10lb bottle its hard to go past as the oz nos comes with no bottle

Brett

Single fogger wet system, running a 50 shot I think or a 75 hahaha one or the other, be careful though the oz nos system looks like good value but when a NOS brand single fogger wet system is only $850 now with a 10lb bottle its hard to go past as the oz nos comes with no bottle

Brett

say i buy the real "NOS holley" setup , with everything....is it still cool to hook it up & use it only once every while? like @ drags etc.,.

& being in nsw, can i cruise around & not get done by cops as long as i dont have the bottle in the car yea?

Mate its the single fogger wet system you need as the holley set up is for a carby, yep as long as the bottle isn't in the car you'll be fine and yep its fine to use every now and then you might just need a after market ecu to be able to take a couple of degrees of timing out if you plan on running anything bigger then a 50 shot

All testing should be done on a dyno though to check if it needs it or not

Mate its the single fogger wet system you need as the holley set up is for a carby,

Holly make systems for Fuel injected cars as well as carby systems.

you might just need a after market ecu to be able to take a couple of degrees of timing out if you plan on running anything bigger then a 50 shot

You shouldnt need an aftermarket ECU, just set the mix correctly.

Correct me if im wrong, But if your running 550cc injectors should your car have an aftermarket ecu? It would be over fuelling to the shithouse as the the stock ecu is already programmed to run rich mixtures?

Is it really that safe running NOS without Aftermarket PIstons?

Is it safe to increase boost without aftermarket pistons ?

There comes a point for any engine where enough is enough. The rb25det seems to be OK up to 250rwkw, so an extra 75hp of NOS at this point might be pushing it too far, but if you are only putting out 150-200rwkw, then a shot of NOS is probably your cheapest way to get that much power.

if you can use a diffrent brand it would be ok.

i had a faulty nos solanoid with my very first nos setup . it was a OZNOS type wetkit and the nos solonoid didnt shut so even though i had the switch of it was still throwing nos into the motor :( lucky i had a passanger that could reach the bottle and turn it off.

since then i have had two NOS BRAND kits and never once had a problem.

good luck with what ever you end up doing.

Hey guys - dirty-cheaterer-pusseh here :(

I run a 75hp NOS brand wet nitrous system using a single fogger plumbed between the factory BOV location and the throttle body.

It works great. Boostn247, dude, just come to myhouse and have a look. Bring your notepad and a pen ;) Gimme a buzz - 0416271834

Adrian

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm selling my personal race car. 1992 BNR32 Skyline GT-R About eight years ago the engine developed the dreaded low oil pressure problem. I removed it and found the issue. However shortly after I moved half way across the country, moved my work shop, bought a house, got married, then moved my shop again to it's permanent location for the time being. in turn I do not have the time to race this car as it should be. In turn the engine I built for this car will end up in my street car and this car I hope finds a home with someone who can use it to it's full potential. The roll bar was built by Jason Noren Fabricaiton in Pomona California to SCCA and NASA Specs. The car used to compete in redline time attack and global time attack enthusiast class. It also has a fire suppression system.  The car is with me at my workshop in Kyle Texas, USA. Shipping it is no problem, I can personally deliver the car to the port of either Houston or Los Angeles. Any other port depending on where it is may require transport but we can always work that out.   The chassis itself is rust free, rear quarters and under fenders are free of any rust so it's a very solid foundation for anyone who wishes to move forward with it. As posted and at the asking price of $20,000 USD the car includes all of the following;   All OEM Body panels, front fenders, rear bumpers etc.  OEM Nissan Projector headlamps (Pictured N1 lamps were removed) OEM Nismo Side Skirts / Extensions OEM Rear Spats  Front & Rear Subframes are installed car is full roller Rear Subframe has Cusco Camber Arms, Whiteline HICAS Elimination Front Subframe has Whiteline tension rods and whiteline Sway bars w/ endlinks.  Buddy Club N1 Coilovers All chassis wiring and engine wiring is in tact. Attessa System is fully in tact and was functional before engine removal.  BCNR33 GT-R Brembo Brakes F+R with Endless MX72 Plus Pads, DBA Rotors & Stainless Steel Brake lines Billion Racing Radiator Billion Radiator Hoses Fluidyne Engine Oil Cooler Accusump System (trunk Mounted) 5 Speed Transmission w/ Transfer Case F+R Prop-shafts Rear Differential With rear Axles.  Nismo Gauge Cluster Nismo Clutch + Flywheel   Essentially what is needed to make this car running and driving again is as follows: A working Engine, an ECU, and time to put it together. The price posted is or best offer as I am willing to remove some components to accommodate price to a certain extent. If any serious buyer wants full detailed pictures, videos, or any questions I'll be happy to answer them. I believe this car is priced to move quickly considering it's a rust free and very straight chassis but always open to fair negotiation.  I can be contacted via phone or email. (+19517081648) email is juan@bardabe.com   
    • So...to my (and my mechanics doing the swap) surprise...the oil pan from NEO engine does not fit 100% and needs to by modified like this: It is not a huge problem but in the future i want a "proper" oil pan. So question is...what different oil pan can i get to fit without any problems and modification? Thanks! 
    • Some more info I found.  These are the last entries Yoshikiyo Fujii made on his blog before he passed away in 2009: http://blog.livedoor.jp/fujii_dynamics/ And finally this is where the workshop was situated:  https://maps.app.goo.gl/HhTPtHzt3WVcBTiEA  
    • shit boxes, kids, and daily drivers are all welcome
    • Cam seals go hard. It's a very old car.
×
×
  • Create New...