Jump to content
SAU Community

Automatic Transmission Shift Kit. - Updated Oct 2006


Recommended Posts

Great news tikki169.

Have fun giving those manuals a run, I now find that in a street drag (on private roads of course) that even if we pull off at the same time and at the same rate, the gear changes will be where I pull ahead.

I have to agree, bang for buck it makes a great difference to the drive.

Put mine in myself the other day also,

will post some pictures etc in the next few days when i get the camera and computer together :rofl:

fairly big difference, feels a little more responsive everywhere but gearchanges are where its definately heaps better. gearchange times have been cut in half if not more.

i got about 5.5L out from draining and replaced with transmax z,

Auto is running great now

Don't know if anyone else has noticed but mt fuel economy has actually gotten better. I'm now getting 360-370 KM per tank where as before I was getting 330-340. That's city driving with hard take offs.

Definately worth it,

I did some proper full trottle runs the other nite and i must say im pretty impressed, been awhile since ive got home with a big smile on my face :P

gotta get some tuning done and some other little tid bits but with a good launch im hoping to see low 13s consistantly

OK, the Valve Body is in and I'm very impressed.

The gear changes are much quicker. It takes aprox. three times less to change gears than before.

The ride quality hasn't changed much. The only difference is from first to second, it's not as smooth as before, even with light throtle, but with full throtle it chirps easy.

I'm very happy with the result and I highly recommended.

Great stuff nedb

Spread the work and remember to return those old valve bodies so that others can get their kit posted out.

I'm glad the rest of you are as pleased as I was with this kit. I was initially worried about recommending the kit (I dont usually recomend anything unless I am sure) for fear that others wouldnt think it was as good as I did. I think bang for buck it is probably up there with a new turbo, it makes a huge difference.

It would be great if somebody did before and after dyno runs with no other changes.

I think we would see some interesting results. :cheers: My seat of the pants tool can feel quite a bit of difference. :(

Why I think there could be a difference in power is, it feels like there is more torque now and there's possibly less power loss through the gearbox.

It could be one of those placebo effects but i'm happy. :cheers:

But again some other facts in my case: my gearbox has done more than 150 000 and it has just been refreshed with some RedLine stuff. So the new valve body and the fancy fluid has definitively made my car feel different.

Just saw this thread now, but is this group buy still running? i.e. would i still get a discount on the price if i ring up now?

Yes its still going. Ring MV Automatics (see page 1 for details).

hey everyone

can someone pls post up some pics as im planning to do this very soon; but have no idea about what i need to do (or where to look for that matter!)

and has anyone done this at a workshop in melbourne?

thanks

I pulled my valvebody out on the weekend and sent it to Mike yesterday. There are sooo many bolts in there its scary. There are about 6 different kinds of bolts too. They are different lengths.

I was really worried so first I drew a diagram with the bolt numbers. Then when I took the bolts out I laid them carefully in the right order and placement. I also took lots of photos.

The problem is that you don't need to take them all out but it's really hard to tell which ones you don't have to take out. I ended up with about 38 bolts out (not including the 30 from the pan) but Mike said I only need to take take out about 7.

The other problem is that the bloody thing never stops dripping transmission fluid all over you so it's really hard to peer up into it and see what's going on without getting fluid in your eye.

Also, I think he underestimated in that some of the wires and and sensors that unplug from the valvebody are bolted in. So you don't need to unbolt these bolts because they hold the valvebody up but if you don't then the thing will be hanging by its wires when you unbolt it all.

After all this stuffing around on the weekend, I spoke to Mike yesterday and he said not to worry about where the bolts all go, just rip em all out because he will put it together properly so when you get it back it will be obvious which bolt goes where. So I am now sending all the bolts down to him.

If you are doing it yourself it might help you to know the following:

There is a black roughly oblong shaped pan thing bolted to the bottom of the valvebody. This is the filter. Unbolt it completely and get Mike to put a new one on. This is general maintenance that you should be doing anyway.

None of the bolts that are covered by the filter require removing.

I suggest you go around the outside of the valvebody taking those bolts off then crack ALL of the rest of the bolts. This enables you to wiggle the whole valvebody around and then you can see which ones are holding the thing up.

Hope this helps. It was a totally new experience for me.

ps have fun playing in the transmission fluid. You will get it everywhere.

  • Like 1

Yeah I know what you mean about the dripping. We're lucky cause I had the new VB with me I just matched up which ones were out the VB and removed them from the VB still attached. Just make sure you see which cprings go where because only one is goingh to go back in. Otherwise not a bad job at all. O and having ramps helps a ton.

I am tossing up between redline high temp and racing.

150 litres came out of the transmission... all over the ground and all over me and about 4 or 5 litres in the drain tub.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi. A little bit of an update. It maybe(hope not) looks like i would need a new tranny(it would be "maybe" a cheaper or better option anyway) So i need some info. I know i need a different propshaft(i can make custom one) LSD is not a problem cuz the engine will be still(for now) N/A RB20. So if i buy RB25DET NEO tranny...is there something else i need? I read something about push/pull type but i do not know if i need to "change" something or i can just plug n play onto my engine a go? Thanks for the advice  
    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
×
×
  • Create New...