Jump to content
SAU Community

no reverse...?? r32 GTR

R32zilla

By R32zilla,
in Engines & Forced Induction

 Share

Recommended Posts

R32zilla Experienced

R32zilla

Posted
Posted

Hi all,

Next problem...came back from a short drive, no issues whatsoever.

Go to select reverse to go for a drive...and I could not select at all. So pushed the car out...and the rest of the box is perfect.

Could it be the reverse shift fork perhaps?

The box has been no problems apart from a very slight notchiness for 3/4th change...

Obviously the box has to come out to check the fork?

:P

Link to comment
https://www.sau.com.au/forums/topic/62974-no-reverse-r32-gtr/
Share on other sites
R32zilla Experienced

R32zilla

Posted
  • Author
Posted
Doesn't reverse share the fork with 5th? does 5th work?

Does it just physically not go into gear? or do its go into gear but just act like its in neutral?

Ferni,

It wont go in at all. So physically it wont allow me to select reverse...

The manual shows a shared OD and Reverse fork rod, but also a dedicated reverse shift fork...

:headspin:

Dave R31 Enthusiast

Dave R31

Posted
Posted

On the R31's, I think the reverse gear has no synchros so sometimes it just wont go into reverse. If you let the clutch out (in neutral) then in again it will then just slot straight in. Try pumping the clutch then trying again. It might be the same on the GT-R box. Worth a try anyhow.

SteveL Mentor

SteveL

Posted
Posted
It wont go in at all. So physically it wont allow me to select reverse...

Question is....can you still get 5th ?? Also does the shift lever still have normal travel when trying to get reverse ??...or does it stop part way ??

5th is 'operated' by a 'pin' link mounted on the reverse shift fork. If you can get 5th, then it's not a linkage problem, but probably a broken/damaged reverse shift fork or roll pin. If you can't get 5th it could be a linkage problem further forward in the 'box, but could also still be something to do with reverse mechanism. There are other remote possibilities like shaft circlips breaking.

R32zilla Experienced

R32zilla

Posted
  • Author
Posted
Question is....can you still get 5th ??  Also does the shift lever still have normal travel when trying to get reverse ??...or does it stop part way ??

5th is 'operated' by a 'pin' link mounted on the reverse shift fork.  If you can get 5th, then it's not a linkage problem, but probably a broken/damaged reverse shift fork or roll pin.  If you can't get 5th it could be a linkage problem further forward in the 'box, but could also still be something to do with reverse mechanism.   There are other remote possibilities like shaft circlips breaking.

Thanks Steve. I can get 5th. I guess trying to fix this issue would be cheaper than getting another second hand box.

SteveL Mentor

SteveL

Posted
Posted
Could be a spring and ball issue locking me out of reverse perhaps?

You could have a look at the reverse check device which is mounted on the passenger side of the O/D case just below the pressed steel cover plate. It's held in by a 10mm head bolt and is sort of 'tear drop' in shape. It's got a 'cam' and hairspring arrangement and I suppose there's a remote possibility the spring could break. But if you've got normal lever travel when trying to select reverse it's unlikely to be that. Anyway, you could try taking it out and seeing if it makes any difference (note it's got a sealing o-ring on the body so might take a bit of levering, plus I'm not sure there's enough clearance to remove it completely with the gb in the car).

There's also a check ball, spring and plug for the O/D and reverse mechanism on the drivers side of the gearbox on the sandwich plate. Again, you could try taking out the plug and see if it makes any difference.

  • 7 months later...
Guest DIRTgarage

Guest DIRTgarage

Posted
Posted
I've heard of the spring going...did you work it out?

Was there an easy way to fix it?

we had a reverse problem.....it was the reverse thrust washer in the rear half of the box....it stopped us selecting it at all....it was in a second hand box we borrowed when we smashed on at Eastern Creek earlier this year.

Beer Baron Grand Master

Beer Baron

Posted
Posted

also check your hydraulics. much cheaper than pulling out the box and it's possible that a dud slave or master is preventing you from completely disengaging the clutch, hence you are unable to select reverse. easiest way to test this is to switch off the engine, then try and select reverse.

  • 4 months later...
cowie165 Veteran

cowie165

Posted
Posted (edited)

*bump*

Hi team.

Same problem here. Gearbox oil is 1,000km old. Reverse no worky. Difficult to engage 5th when engine is off and without the clutch. 1st through 4th engage engine off no clutch.

Reverse does not engage at any time. It does not move on the fork at all. The wasn't any crunch/bang nor any whining in the gearbox prior to failure.

Thanks Steve and Paul for the info! It gives me something to go on.

Here's hoping I can sort this out in the garage... it crumped whilst taking my wife out for our wedding anniversary! :P Sure puts the pressure on at the shops when you only have one shot to nail the parking space. :)

@R32zilla: Mate did you sort this out in the end?

Edited by cowie165

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • MBS206
      RB20DE NEO smallbox clutch.

      By MBS206 · Posted

      From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • MBS206
      Lock up the old for sale / wtb threads.

      By MBS206 · Posted

      That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...