Jump to content
SAU Community

Recommended Posts

hey Guy's, put my car on the Dino the other day down at evo in fyswick just to see how much power my pritty stock r32gts-t put out. i got a reading of 137.4 kw at the rear wheel's wich is about 185 bhp. I was just whanted to know if any one can tell me what that is a the fly wheel, as stock its suposed to be 160kW @ 6400rpm (214 bhp) and just whanted to know how much more power mines got from stock!

Thanks

some say theres as much as 20% loss through the g/box, diff etc, but it all depends on the types of g/box, diff. there was a thread about drivetrain losses in another section a little while ago, cant remember where it was though.

what mods have you got?

It's hard working it out in reverse as a %.

I think the expected losses are about 50kw for a manual rwd R33 gts-t, and around 60-65kw for a manual 4wd (GTS-4 or GTR). Higher again if you've got an auto transmission.

So a manual R33 GTS-t at ~180kw at the motor comes down to ~130kw at the rear wheels.

Remember that your motor generally won't be putting out what the factory spec's are due to the age/wear etc..

J

list of mods:

Greddy Large front mount Intercooler,

Cusco Aftermarket coil over Ajustable suspension

GTR front spoiler

17 inch alloy wheels

4 inch Apex Exhaust

Strut brace

blitz Air Pod

hks Blow off Valve

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • She swallowed the spider to catch the fly.
    • Half anticipating the next question then: I have two magnets stuck in my oil pan. What should I do? 
    • If it's magnetic what is stopping you from using a magnet on a thin wire from fishing it out?
    • Those 2 solenoids in that assembly I mention, are the PWM solenoids for torque converter lock-up clutch & EPC (line pressure control) ~ when most folks hear of 'solenoid failure', the tendency is to think electrical failure...but fact of the matter is, especially wrt the EPC solenoid (which is moving/running all the time), you can have an electrically 'good' solenoid, that's absolutely broken/worn out mechanically inside...ie; valve plunger return spring rubbing against spring retainer plate, lowering preload pressure.. ...and the solenoid armature extension limit spring wafer with bad wear/broken off petals... ...and if there's ever been any metal flying about, damage to the valve plunger end itself... ...the stuff one never really sees, unless you go the whole 10yards trying to answer the question "why is my line pressure screwy, but TCU isn't flagging any EPC solenoid fault?"...and carefully dissect the solenoid. Worst (and most probable) scenario is when the plate spring petals break off, they get held by the magnetic flux, get mashed up by the armature into little bits, which end up in the space between the armature & shading core bore, and things get stuck or randomly jam up, and your line pressure goes flat and doesn't change...and the TCU never sees it, as it doesn't actively monitor LP... ..then it gets into insidious land, if you end up with lower than expected line pressure...lets say high clutch..and the lower pressure causes it to slip ~ when I say 'slip', think say 2000rpm on the drive plates, and 1800rpm on the driven plates, because the slip is making them under-rotate by 200rpm ; you get all the usual nasties like heat and band/clutch wear, but even if it's only 20rpm slip the same thing happens...and... you'll hardly ever pick this up driving the thing with the torque converter active as it effectively masks these sorts of slippages that are line pressure related ...(the newer TCUs can detect clutch slip rate)...just  FYI as it were...  
    • There's nothing that some paddle pop sticks and extra cable ties can't fix.
×
×
  • Create New...