Jump to content
SAU Community

Recommended Posts

hi guys just a few questions 1 is do all gtie have quad throttle body's, 2  whats a stock gtir do on the strip and on the dyno, whats the best mods to do to them to make them go

A stock Gtir does around 14.2 sec on the quarter and the best mods for them are the same as any Jap Turbo ie FMIC, dump pipe, exhaust, pod filter, ebc set at 1.2 bar, fuel pump, power FC and coil overs should get you started.

The good thing about those cars are that the stock turbo (T28) isnt limited by the ceramic exhaust turbine that skylines are, so you can push them a fair bit harder.

From my understanding all Pulsar Gtirs have quad throttle bodies and solid lifters.

Link to comment
https://www.sau.com.au/forums/topic/64060-nissan-gtir/#findComment-1202825
Share on other sites

yes, as posted above all GTI-Rs have quad throttles and a nice steel wheel T28 which is good for up to (and sometimes just over) 180kw at all four.

A stock GTI-R will run anywhere from 14.3 down to 13.8 depending on the condition of the car, and who is driving it. on the dyno a stock GTI-R should make anywhere between 105kw atw up to 120kw atw again depending on conidtion and dyno.

best mod for your stock GTI-R is some good brake pads, good rotors and braided lines with some good fluid too. cause stock GTI-Rs are quick they just don't stop too well if the brakeing system isn't in peak condition. after that exhaust (dump, front and the rest), then some kind of high flow filter or pod with air box and cold air intake. wind up the boost to around 1 bar, and get a front mount if you want. you will now have anywhere between 140 and 165kw at all four and have a car that can do low somewhere between a high 12 and a low 13. NOTE: your clutch may now be on the way out, if so upgrade. now you'll need to make it handle properly so start with a bigger rear sway bar and replace every suspension bush you can think of with some urethane ones. now if you still have money start looking at coil-overs and most importantly get the suspension set up somewhere that knows what they are doing. now you have a very nice street car, but be aware that unless you are going to keep and enjoy it for a few years you will be dissapointed when you sell it. they are great little cars though.

Link to comment
https://www.sau.com.au/forums/topic/64060-nissan-gtir/#findComment-1202836
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks again, really helpful chap from alpha omega wanted to speak to me, little concerned if this is meant to he aero alloy/ airospace quality and car sitting on drive has caused this.  Airplane are subject to much more changing temp and conditions than road salts! My caliper, many other components much older have surface rust but never eating part of the metal   Had I not seen it , could have been a disaster! specifically on rear part of bracket coming off like biscuit will update on what they say, helpful people so far
    • January or Feb is it booked in for turbo fitment?
    • The MX5 has had some annoying rattles in both front doors over bumps So I installed fancy pants door bushings, which stopped all of the rattles with the windows up, but........with the windows down there was still rattles, so after some googling,  and a chat with MX5 Mania, I got some new door to glass weather seals, all the rattles, windows up, or down, are gone now Shout out to MX5 Mania, the weather seals were on sale, and when I head to Dural to pick the up they even fitted them for me for free I did see a "really" nice Blue NA sitting out front   and this Black NC PRHT that looked like it has sat in the sun for its whole life and never had a wash, the clear coat was non-existent, an it looked horrible, really horrible, but, it had a nice turbo kit with over 200kw, the thing went like a cut snake, bagging the rears through the gears and dosing like a champ 😍 But, as I've always stated, I am keeping my NC na, I'm happy with the current power the car makes In other news: MX5 Mania do a drive in drive out turbo kit, the only minor additional part recommended for boosting my car, as it sits now, is a oil cooler, and that bonnet vents are definitely required for track use Aftermarket version look a bit to "racecar" spec I wonder how Focus RS bonnet vents would look?????
    • Paint is only structural when applied to the outside of Chinese and Indian cars. Otherwise it should never be present between mechanical joints that were intended to be metal to metal. Pain slips, slides, cracks, compresses, and add thickness that wasn't intended to be there. It comes firmly under the category of "just no".
    • appreciated it thanks   There are threads on the adaptor. I rear re anodising but didn’t know it will reduce strength   re mating services needing to be flat/ not painted, why would that be? I am devastated as car been off for a year, fixed power steering then installed bm57 master cylinder and just before driving it this came up. So annoyed   worried and afraid to drive it, no fun caliper coming off    
×
×
  • Create New...