Jump to content
SAU Community

Recommended Posts

It means intermittently there's a problem with the 4WD system.

In the boot, in the RH corner, behind the lining, there's a fluid reservoir. Check the fluid level is between the marks (check with engine running). Takes auto-trans fluid.

Otherwise, there's a faulty earth contact (maybe, have fun finding that one!). But I would lay money on the fluid reservoir.

Link to comment
https://www.sau.com.au/forums/topic/6413-4wd-light-on-gtr/#findComment-96131
Share on other sites

Originally posted by blind_elk

It means intermittently there's a problem with the 4WD system.

In the boot, in the RH corner, behind the lining, there's a fluid reservoir. Check the fluid level is between the marks (check with engine running). Takes auto-trans fluid.

Otherwise, there's a faulty earth contact (maybe, have fun finding that one!). But I would lay money on the fluid reservoir.

I think its somewhere different on R33. Can someone confirm this.

Link to comment
https://www.sau.com.au/forums/topic/6413-4wd-light-on-gtr/#findComment-96178
Share on other sites

My car also does the same but it happens if the car is idling for more than 2 mins.. You can actually hear the 4WD drive pumps running and as the light turns on the pump turns of at the same time... while in traffic i turn the car off and then back on and it back in 4WD drive mode...If i take of while the light is on then its in RWD....

This is quite annoying especially as i drive it everyday in Sydney peak hour...So if there is a fix it would be great...And yes i have check the fluid already..

Nick

Link to comment
https://www.sau.com.au/forums/topic/6413-4wd-light-on-gtr/#findComment-96316
Share on other sites

I dont think the reservoir being full or near empty is that important...if its bone dry maybe but as long as there is oil in there.....and someone correct me if i am wrong but i think it doesnt have anything to do with the split drive system...I had an R33 GTR before and have replaced the clutch in it myself and it looks as tho that oil is the feeder for the gearbox oil...i was under the assumption that the gear box works on the Drysump principal....i may be wrong but thats what i can gather and it looks like the split is further towards the front of the gearbox on via a clutch pack in the transfer case ....i would be checking for computer related problems ...run an on board self diagnosis test and see if you can extract and codes from the ecu.

Link to comment
https://www.sau.com.au/forums/topic/6413-4wd-light-on-gtr/#findComment-96679
Share on other sites

Originally posted by blind_elk

It means intermittently there's a problem with the 4WD system.

In the boot, in the RH corner, behind the lining, there's a fluid reservoir. Check the fluid level is between the marks (check with engine running). Takes auto-trans fluid.

Otherwise, there's a faulty earth contact (maybe, have fun finding that one!). But I would lay money on the fluid reservoir.

O k I just went to check it out. The the empty max mark is halfway on the bottle which the fluid should be in between right?

The bottle on my car is "totally" full!

Can this make the light come on?

Link to comment
https://www.sau.com.au/forums/topic/6413-4wd-light-on-gtr/#findComment-97146
Share on other sites

Does your abs light flicker before the 4WD light comes on?

The bottom part of the reservoir is the return. If the air gap between the fluid in the bottom and the top part is the big you may need to bleed the 4WD system. There is a max gap something like 5 or 10 mm.

Another common problem is earthing.

You can get an error code out of the 4WD computer. I forget how to do that, I can look it up in the manual on the weekend.

Link to comment
https://www.sau.com.au/forums/topic/6413-4wd-light-on-gtr/#findComment-97447
Share on other sites

Originally posted by nis14

Does your abs light flicker before the 4WD light comes on?

The bottom part of the reservoir is the return. If the air gap between the fluid in the bottom and the top part is the big you may need to bleed the 4WD system. There is a max gap something like 5 or 10 mm.

Another common problem is earthing.

You can get an error code out of the 4WD computer. I forget how to do that, I can look it up in the manual on the weekend.

Thanks much appreciated. I will will drain my fluid to the correct level first and then bleed if I have too. I will wait for the error code posting

Thankyou once again.

Hey RH9GTR I know how you feel LOL

Its annoying!

Link to comment
https://www.sau.com.au/forums/topic/6413-4wd-light-on-gtr/#findComment-97459
Share on other sites

There is a procedure to bleed the 4wd system. From memory on a 32gtr it goes something like,

1. fill the reservoir to about 3 cm over the max.

2. remove the air from the bleed valve on the unit above the rear diff.

3. turn the ignition on

4. disconnect the bleed connector which is behind the kick panel near the accellerator pedal. It should be a white or yellow wire with an inline connector that you need to disconnect. You should hear the pump start for a couple of seconds.

5. there is a bleed valve on the back of the gearbox/transfer case, you need to unscrew it nearly all the way, then open and close it quickly for 1 sec at a time. You should hear the pump pulse then close then value. Do this until all the air has gone.

6. there is pipe (the return) on the side of the reservoir on the tail light side (the reservoir is on the right hand side in a r32). Open this to drain the excess fluid by connecting and disconnecting the bleed connector near the accellerator pedal. The pump should turn on when you connect the bleed connector if not turn the ignition off and off then try again.

7. connect the bleed connecter and turn off the ignition.

Sorry for the confusing explaination, it is easier with pictures although the engrish in the manuals is probably worse.

Unfortunately this didn't help my friend, his problem is abs or electrical related.

Link to comment
https://www.sau.com.au/forums/topic/6413-4wd-light-on-gtr/#findComment-97526
Share on other sites

DR,

I have the same problem, except my ALSD light comes on as well. If the fluid is over 12 months old replace it. Mine is just getting to 12 months now and I have noticed that the lights are starting to come on more frequent. Bleed the system almost completely making sure you keep re-filling the 4WD Bottle.

I have also noticed that removing the connection from the computer under the back shelf and using some connector cleaner on the plugs also stops bad joints which also can bring the light on. If this does not fix it, then sell it and buy another one. I have a friend who spent $20k and 10 months and he could not find anyone in Sydney who could fix it. His come on continuously so it was a slightly different story.

Link to comment
https://www.sau.com.au/forums/topic/6413-4wd-light-on-gtr/#findComment-101273
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If that's the wiring from the factory, I'd be inspecting the loom everywhere.   Any signs of that anywhere else, and seriously, I'd get rid of the car ASAP before the electrical gremlins make it worthless, or it goes up in flames on its own. That is scary how that insulation is failing!
    • I should note too as I have all 4 wheel speed inputs to the emtron I now have the emtron controlling the attessa solenoid for 4wd/traction and launch control strategies. 
    • It works quite well with the adjustibility within each of the programs of the turbolamik. Essentially p1 is drive and lockup comes on like a normal driver.  But in program 7 I have customised it to not request the lockup clutch to engage until something like 6500/7 when slip was the lowest. 
    • Yep, I like that. The tags are only on the first post of a thread and we don't get huge numbers of new threads. Also, I plan to add some more report types and we could have a member report type like 'review tags' then members could flag if they thought a topic wasn't tagged correctly.  No way man, I dig the input. Thanks! 
    • It's a valid thought. There's not exactly that functionality already (when creating a thread) - that's where the OP can use/create any tag they want. We'd have to come up with a way for the user to request their tags get reviewed or something. Otherwise the mods would have to review every new post's tags (for those that have them, anyway). There's kind of that functionality already exists to some extent, post facto of starting the thread, where the OP or any other user could report the post to admins, and request that tags get reviewed. We could do this already, and any user could already have made such a request. To make it a part of the forum proper, it would require an initial and an ongoing education programme, so that people know that it's a thing. OP based tagging/request for review would also require at least some (probably most) of the user base to be told that it's a thing they can do. Both of these things probably wouldn't spread too far and/or get used very much. If it was the standard approach on a lot of different sites, then it might do, because people would be used to it. Prank's approach to this differs from my original thought, by leaning into tagging. Which is fine - it's possibly better than what I originally suggested. In fact, I just went to the R32 GTR wiring diagram thread and added tags, including "Library". That's probably a good way to use tags and the idea of a library. We just have to drag together an (organised!) index of threads or posts that have that tag. I have yet to do any of my own follow up by pursuing worthy threads and posts and reporting/marking/tagging them for the library, such as the @Sydneykid stuff I was talking about, and possibly any amount of @Lithium 's and others' posts. At least if I tag them Library, we'll have a start.   Back to @Wazmond's idea as it relates to @PranK's, we might have some sort of a list of tags that are already used to scrape for this library. I'm not entirely sure how that would be presented or used, particularly if it got long. But it's yet another idea!   cheers
×
×
  • Create New...