Jump to content
SAU Community

Recommended Posts

Hi all,

Thought I'd start this thread to try to help out anyone who has problems with the backlight on their climate contol unit.

Mine was 1/2 gone then after replacing my stereo it was totalled ! I realised that the globes are replaceable after reading NZSTAGEA's post on the stereo replacement thread but had heaps of problems finding replacement parts.

I went to a number of auto electricians, dicksmith, jaycar, nissan, and a couple of hobbie shops and was unable to find a bulb that had long enough contacts. I was in another dicksmith store for something completely different and after rummaging through their electrical compoents I stumbled on one that looked close.

I have now fitted two new bulbs and the unit is working properly. The part details are as follows:

part number: P8140

Description: Globe, 12v, 50ma, 5mm wheat grain

Price: $1.28

To fit the bulb:

*Follow stereo replacement directions to get the CCunit out

*unscrew the bayonett fitting in the top of the unit.

*remove the rubber bulb covers carefully

*unhook the bulb wires from the bayonett fitting & remove the bulb

*fit the new bulbs in the bayonett fittings & wrap the contact wires around the inside (side that the bulb is on) of the fittings.

*replace the bulb covers ^

*replace the bayonett fittings

*replace the CC uinit

^ optional - I lost one of my covers so did not fit the other and the unit works fine (but backlight is now orange !)

Link to comment
https://www.sau.com.au/forums/topic/64577-climate-control-part-number/
Share on other sites

  • 2 weeks later...

Another query with aircon...

only a minor annoyance - but stag is first car Ive driven where the climate control doesnt keep memory of the aircon setting when u switched the car off... every time u get in the car it is by default switched off... just irks me coz if I hop out, pop into a shop - pop back in and turn key - it doesnt go back to my preferred aircon setting i just had... so i have to switch it on, readjust it etc every time...

So yeah - any1 know of anyway around this - so that when i turn the car on it is on the same aircon setting it was when i last turned the car off???

:D

Check your fuses. I had this problem when a fuse had blown somewhere, but i forget where.

Make sure you check for continuity with the fuses, as sometimes they look fine but are actually stuffed

  Brazen said:
Another query with aircon...

only a minor annoyance - but stag is first car Ive driven where the climate control doesnt keep memory of the aircon setting when u switched the car off... every time u get in the car it is by default switched off... just irks me coz if I hop out, pop into a shop - pop back in and turn key - it doesnt go back to my preferred aircon setting i just had... so i have to switch it on, readjust it etc every time...

So yeah - any1 know of anyway around this - so that when i turn the car on it is on the same aircon setting it was when i last turned the car off???

:(

Could be a fuse issue as Terminal says, could also be a wiring problem. I believe the climate control unit has a 12V feed from the battery when the car is off (v. low current) to maintain the last set temp in memory. So it could be that this feed is either disconnected, or someone has bodged the wiring and connected it to the ACC feed.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...