Jump to content
SAU Community

  

65 members have voted

You do not have permission to vote in this poll, or see the poll results. Please sign in or register to vote in this poll.

Recommended Posts

Ok, well Ive put a small deposit down on this car pending a full check over next friday at Hyperdrive so im not 100% locked into getting this car however the price is VERY good its done 88'000kms, its manual and Its advertised as:

GTST - MANUAL Series II M-Spec 1996

Now the front bumper/body kit was very badly damaged when he drove it up/down somebodys drive way "explains why its got a new one unpainted on the front"

But its not a SII front at all is it??

Im attaching some picktures so you guys can ahave a look and let me know what you all think.

Series 1. 1.5 or 2

* its advertised as II and I looked on his rego papers and it was registered as a Series 2.

Link to comment
https://www.sau.com.au/forums/topic/65086-gts-t-r33-series-i-or-ii/
Share on other sites

  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

I dont think it had a passengers side air bag. The dash and everything looks so damn clean.. almost looks new.. Its on a slight tilt towards the driver " the radio etc etc.. isnt that a series 2 design?

Butler: Yeah? The front bumper isnt stock

if it didnt have a passanger airbag its definatlly not series 2. But because it does have one in steering wheel it will be series 1.5 hey. Have a look at some pics for a 95 skyline and a 96 you'll see that the steering wheels are different. Those pics show a 95 (series 1.5) steering wheel.

if it didnt have a passanger airbag its definatlly not series 2. But because it does have one in steering wheel it will be series 1.5 hey. Have a look at some pics for a 95 skyline and a 96 you'll see that the steering wheels are different. Those pics show a 95 (series 1.5) steering wheel.

Ahh man.. Im worried now.. It must have at least one airbag because it says SRS airbag under the bonet, It also is dated as a 1996 build under the bonet.

Cheers pozza, Im going to look into the 1995 and 1996 models a bit more..

Its 100% a 1.5...

Has a series 2 motor with series 1 interia and series 1 front end (ie grill, bumer and most importantlly headlights... The series 2 has different head lights. If its a 96 model it cant be a swries 1.. It can only be 1.5 or series 2....

Must be a 1.5, as why would someone replace series 2 stuff with series 1 parts...

Sounds dodge, I've seen a Series I for sale from the dodgiest guy I've seen and it was badged under the bonnet as a 1997.

He even asked me what's the difference between a I, II model !

I think someone on here has a way of telling the year by the chassis number of something,

No that's not a Series II at all, headlights, bonnet, grille, front bumper, interior are all indicating Series 1.5. The only part which is the same as a Series 2, is the colour coded [skyline] panel at the rear, but all you have to do is paint a Series 1/1.5 clear part and it looks the same as a S2.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • HKS trigger kit should be very easy to integrate with a Link. It's a 36-2 crank trigger. Hard part is finding the motivation to take off the timing belt and everything on the front of the engine to install it. You also need to cut out a hole in the oil pump housing so the sensor can read the trigger wheel. Changing out the cam sensor for a 24 tooth setup is probably good enough but as others have mentioned depending on what underlying assumptions are changed it becomes more of a problem. Reading the crank state off of the cam is an abstraction that works in the general case, but if you have an edge case it makes less and less sense. There is a GTX2860 gen 2 that can take a compact 5 bolt housing so it's direct bolt on but I'm not 100% sure of what's involved. Peak compressor efficiency drops off a bit on these turbos vs -5s, 77% vs 73% but you get way, way wider region of operation. The -5s have a really strange surge line in their compressor map that is all over the place. If you think the hot side on the -5s aren't open enough you can try the Tomei T550B turbos which a local tuner seems to be happy with:
    • i need a complete tail light for my R33 GTR if you have please let me know.
    • I need a great maintenance workshop around Idaho, if you know one please let me know..
    • Hello friends, i have a good friend in Canada that looking for a good condition 1993 GTR around him please if one or know someone around you that is willing to let it go please let me know so that i can inform him.....Thanks
    • I'm mark from Idaho.
×
×
  • Create New...