Jump to content
SAU Community

GTR Complete Turbo Kit $2200ono (HKS)

buttocks
 Share

Recommended Posts

buttocks Collaborator

buttocks

Posted
Posted

GTR turbo Kit (T51?)

Kit includes

Turbo (not entirely sure what it is Heres the INFO i have (When i bought it they said it was a T51 turbo)

HKS Turbo (guessing from the logo on the rear cover)

Garret Front Cover

HKS exhaust Housing

Compress wheel is 7cm across

Exhaust Wheel is 7cm across

A/R .72

Front compressor bell mouth 10cm across

Serial number on turbo - WG 7011J

Seems to be in Good condition

Thats all i have on the turbo

Heres what else it comes with

Dump pipe just over 1 metre in length

Twin air filter to Bell mouth Pipe

Intercooler pipe with Greddy adjustable Blowoff valve

Alloy shrouds (heat) 2 off for the Manifold etc

Exhuast manifold with pipe running off for External Gate

And what looks to be a alloy pipe about 50cm long looks like a External gate Dump pipe

Sunshine Coast QLD

0438145562

Welcome to come have a look!!!!

Only advertised here so far

Wish i could test it but i haven't got a GTR and wish i did

Link to comment
https://www.sau.com.au/forums/topic/65349-gtr-complete-turbo-kit-2200ono-hks/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • r34killa
      General interior R34 questions

      By r34killa · Posted

      Hi everyone, I'm generally new to DIY projects, and I've browsed this forum and watched a lot of youtube videos but still have a few questions   Firstly, how does spray painting interior hold up? in particular like vinyl parts, my current mode of thinking is to use methyl spirits to take off original paint, clean/prep well, light coats, no primer or clear coat    Secondly, what is recommended for the headliner and, for example (my car is a r34), the A-pillars which are some kind of other fabric material, do you think I would be successful at retrimming these? or would it be better to go down the blacking out via Dupli-Color Vinyl & Fabric Paint    Any other advice / tips / tricks for refreshing/modernising these interiors?    Thanks
    • D.s
      WTB-R32 gtst front bar-sydney

      By D.s · Posted

      As title says  Pm a photo with what u have  Type m style would be good As Hidding a thick front mount
    • Duncan
      One Headlight isn't working - Driver Side Fuse Keeps blowing

      By Duncan · Posted

      Just note that when trying to find a short in a globe power supply, it is best to disconnect the globe as it will allow current through to earth. With it unplugged it is easier not to get confused. Also with the r32 wiring, the high beam has 2 power supplies (one when you push the switch forward and the other when you temporarily pull it back; so if it is the high beam blowing you will need to trace both circuits
    • dyl33
      R32 gtst Center bearing (brand new)

      By dyl33 · Posted

      $75 Location: Gold Coast  Can post via Australia post
    • GTSBoy
      One Headlight isn't working - Driver Side Fuse Keeps blowing

      By GTSBoy · Posted

      That's a short. Find the short. It will be somewhere between that fuse and the headlight. Start by removing the plugs from the back of the headlight and dimmer switches, and measure resistance to earth. Supply side (power from the fuse) should have none. The other side should have resistance compatible with whatever globe(s) is there (which is relatively easy to say for a normal globe, perhaps not as easy to say for LEDs). Anyway, if you have very low resistance, you defo have a short. Then you just have to run the wiring like you're running the bowel of a dog (on the operating table) that has swallowed something it wasn't supposed to.
×
×
  • Create New...