Jump to content
SAU Community

Recommended Posts

  • Replies 124
  • Created
  • Last Reply

Top Posters In This Topic

Picked up my copy last night. Good old 24hr Kmart. Got the very first copy too :P Pretty damn good so far even with just a controller its still good. Going to take some time to get used to the weight shifting under brakes in this one.

Ive been using two setups for GT3. One involves a custom built (for something else) box. It's about two foot high. For seats I used two bean bags. Another setup is for Driving Force which has a knee holder thing, I just sat on the couch with that one. Both are quite comfortable. I must say though that I haven't tried DFP with the knee clamp, i doubt it will work too well, because of the 900 degrees and stronger feedback.

HAHA just took an M3 for a spin on Neuremburg (pardon my german) ..........HOLY SHIIIAAAAAATTTT..

this track is insane!!!! this is gonna take forever to master. it's the tightest, fastest, crazy one turn after another track there is. it's sooo long.

anywayz i'm going back to play some more .

ciao

I have to wait till 5, then the next 4 days will be spent collecting cars :P

What is the stuff from the old game you can carry over, its $100,000 from GT3 and the tests from GT4P, is that right?

MMmmmm VERY impressed with this game.. Pre ordred it a while ago. Was there at 9AM to pick it up and have only just got off it. (need to get a Memory Card)

I can see this game causing arguments with my girlfriend... she will want to watch tv but I will have other ideas!

:P

I can see this game causing arguments with my girlfriend... she will want to watch tv but I will have other ideas!

 

:P

thats why i pluged my ps2 into the pc... now i think our aguments are gonna be more along the lines of "you play that thing too much" hehe

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Welp, too late already committed to the cam cover breathers to be welded on. I did think about adding a catch can in line with the drivers side sump breather as a phase 2 along with a drain to the sump on the original catch can but with an inline ball valve so I can have it closed if needed.    Likely a single breather would have been enough but I think I’m overcompensating to hopefully not have to empty my catch can and clean up oil over flow every session.    out of curiosity has anyone actually measured crank case pressure before and after various mods? I’m considering adding a sensor for science 
    • Is it a dog or synchro box? I guess either way, if it is new and crunching in one gear only, it has to come out and go back to the shop to check/measure as there is either an assembly or manufacturing issue
    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
×
×
  • Create New...