Jump to content
SAU Community

FMIC install -NOW engine Randomly Cuts-Out

Kaido_RR

By Kaido_RR,
in Engines & Forced Induction

 Share

Recommended Posts

Kaido_RR Grand Master

Kaido_RR

Posted
Posted

hey,

I got My FMIC install on monday, after it was install i had it on the dyno and had my ebc tune so now i am running 12psi (0.8bar) now i have a problem when i am driving the car, doesnt matter what style (it has happen when i was driving normal and giving it some stick) basicly what happens is the engine dies, it just cuts out :( But the really wired thing is that if i just re-start it the car will start fine and there isnt a problem.

I have check the following items and they dont seem to be the problem, IC piping all connect up and no leaks, afm plugs, fuel pump :S

I am all out of ideas :S

PLZ someone help its starting to piss me off :@

DRFT 14 Collaborator

DRFT 14

Posted
Posted

Did you modify the BOV in anyway when you installed the Intecooler and new piping? Check that the hose that goes from your BOV to you intake is still attached securely. Your problem sounds like what my car did before I went over my blow off valve setup.

Angry Proficient

Angry

Posted
Posted

sure it isnt your silcone joins on your cooler and piping? ..mine did this for a while until i blew the hose off completely.

double check your clamps ... start your car ..and grab some CRC ..spray the edges.. and if any of it gets thru . your idle will change.. meaning the crc is getting thru into your inlet.. meaning u have a poor join in the silcone or your clamps are on c0ck eyed

just my thoughts

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      R32 owner from ACT

      By Dose Pipe Sutututu · Posted

      Actually I drive my own cars very hard, much harder than other people's cars, even rentals I treat with respect.
    • DraftySquash
      RB25DET Engine Oil Dipstick Length

      By DraftySquash · Posted

      It didn't save me any money! All it did was leave me with 3x 5L Engine oil bottles that have about 1-1.5L left in them 🤣
    • soviet_merlin
      Cleaning my wheels 😍

      By soviet_merlin · Posted

      Have you tried one of those wash mitts @PranK? I find it works so much better than brushes on a stick for cleaning wheels. If fingers fit between the spokes, then can easily clean them with a mitt. I like Bowden's Own and use their Love Glove, as gay as it sounds. https://www.bowdensown.com.au/products/microfiber-range/love-glove That applicator looks super handy! Earmarked for next time I'm splurging on cleaning supplies.
    • Ozdavroz
      R32 owner from ACT

      By Ozdavroz · Posted

      A car always goes harder if it isn't yours ( e.g. rental, mum n dads, your mates daily when your deso)
    • BourneToLive
      Wiring high beams in IC7 for R32 GTR

      By BourneToLive · Posted

      Hey, guys, I’m hoping I can find answer here. I have already done some searching and asking around but still nothing.    I fitted an IC7 dash in my R32 GTR, and I got everything displaying on the dash except my high beams. I get input voltage and the high beams displaying in the dash when I pull the lever, but not when I fully engage the high beams. I spliced into the Red/Blue Beam+ wire in the black center connector from the cluster, but there is also a black Beam wire I think I need to use as well. The high beams still work. It’s just a matter of getting it to display on the dash.    Has anyone fully wired in their IC7 properly ? I would appreciate any guidance on this.    IMG_8835.mov    
×
×
  • Create New...