Jump to content
SAU Community

Whats the deal with wharfies that thrash cars??

BenA31
 Share

Recommended Posts

Guest

Guest

Posted
Posted
These days I can just see the 'risk' involved in thrashing a car (of any make/model) around a very busy wharf being too high.

OH&S isn't taken lightly anymore these days..

My wifes Dad worked down the docks and I have known them to race new WRX's at night with no lights on so it isnt as blantant as to what they are up to.

Last time I was picking some cars up with my customs guy they had a new Cross Fire and were thrashing it across the dock (it was the lunch run vehicle that day).

Mate was down one time and they parked one of his Soarers to close to a pole and caved the front bar in, lucky for him he got photos or they would of pulled the "it arrived like that, nothing to do with us".

It isnt a myth it is a fact.

Remix- Mentor

Remix-

Posted
Posted
The thought of some smelly disgusting wharfy thrashing my GTR and redlining it just after it hasnt been started for months... makes me nervous.

My car is due next month. This is my biggest fear :cuss:

I shall be waiting patiently with my video camera.

PTR33 Proficient

PTR33

Posted
Posted
Whats stopping a person filiming the workers unloading the cars in an unsafe manner (speeding burnouts or whatever) and sending the footage to Worksafe?
My car is due next month. This is my biggest fear :cuss:

I shall be waiting patiently with my video camera.

Perhaps not a good idea guys.

I heard a story of someone who they caught poking a vidcam through the fence, they beat the snot out of him and threw him and his camera in the tide!!

brett33 Enthusiast

brett33

Posted
Posted
hi, just a quick thought if you're importing a gtr, just discconect the afms, it will default to limp home mode and shouldnt rev past 2500 rpm.... i cant see why this wouldnt be ok for a little while.

Stephen

Sounds like a good idea but if it doesn't have enough power in limp mode to get up the internal ramps of the boat (which it wouldn't) then it'll be getting towed on and off the boat. Which is an added cost to you and more dangerous to the condition of the vehicle.

brett33 Enthusiast

brett33

Posted
Posted
i doubt a gtr would have any trouble getting up said ramps in first at 2500rpm :P  

but good point..

its 2500rpm or 6% injector duty cycle. trust me it won,t make it up the ramps!

Try slipping ya clutch up a steep hill without going over 2500rpm. Na mate it gets towed!

infected flow Rising Star

infected flow

Posted
Posted

uummm where do i start okay for people that are getting there car shipped in a container u can get insurance for it as it cost around $300-$500. this is probably the best as you should get people from japan to take photo's before getting sent so you have reference and also note any damage if it was already there.

About the taper proof seals thats bullshit as soon as the container is pulled off the ship it will be opened as customs do check them and they have to be in quaratine so no foreign disease or insects or any of that stuff comes to australia.

this is a standard procedure..

about the wharfies well it doesnt happen all the time its not a common thing as they will get into a lot of sh1t if they do get caught best thing to do is get a cutoms broker for the container .This means customs will open the container with car in it and quartine car after this the container will be shut with new seals and can be delivered to where ever u like but this also comes at a price ! car will not be started! and car is still in container will seals not broken !

or when u get the b/L u can go to the wharfs and watch them unload and watch your car being handled by the wharfies straight to you!---easy way but involves a lot of time.

hope this helps ill try and answer anymore questions if you have any.....??????????????

brett33 Enthusiast

brett33

Posted
Posted
This means customs will open the container with car in it and quartine car after this the container will be shut with new seals and can be delivered to where ever u like but this also comes at a price ! car will not be started! and car is still in container will seals not broken !

The trouble with this idea is when the car doesn,t pass quarantine (which it more than likely won't) it will be removed from the container and washed and restowed by a wharfy. Not much different i would say.

brett33 Enthusiast

brett33

Posted
Posted
This means customs will open the container with car in it and quartine car after this the container will be shut with new seals and can be delivered to where ever u like but this also comes at a price ! car will not be started! and car is still in container will seals not broken !

The trouble with this idea is when the car doesn,t pass quarantine (which it more than likely won't) it will be removed from the container and washed and restowed by a wharfy. Not much different i would say.

infected flow Rising Star

infected flow

Posted
Posted

hangon ill explain a bit more- u can get the car quarratined before it leaves so when it does come to australia they just give a once over inspection and thats it its free to go but that still doesnt stop you from being there when they do take it out of the container and watch them wash the underside of the car (this is what australia calls quaratine)..lol all they do is drive it to a hoist where u can go with them and lift the car up and wash the underside then a inspector comes has a look to see if it done and then u can take the car ....thats if it does get quaratineed (shit my spelling is bad tonight)...lol...

hope this helps ..

jonn Proficient

jonn

Posted
Posted

I watched the Fremantle wharfies unload the cars of the Bravery Ace for a few hours. I'm glad to say that I didn't see one car being given a hard time. That's not to say it doesn't happen as I'm sure it does but when you see the amount of cars, buses, trucks, cranes, bulldozers, backhoes etc etc that these guys unload and the time they have to do it in, it's pretty amazing.

Definately not defending the pricks that play Colin McRae with our cars. I just didn't see it when I was down there.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JarrettL
      r34 Skyline 25 Gt four GTR conversion (ENR34)

      By JarrettL · Posted

      I know this is an old thread but I have a particular attachment to the ENR34, so I don't think additional content hurts. For starters, I agree with everyone here in that the performance of a stock R34 GTR is a pretty low bar and one that you're going to spend a lot of money "matching". Now if you're willing to deviate from that template as your goal, you'll be much better off and enjoy the car much more. The engine in the NA R34s is a real kick in the nuts in terms of upgradability compared to previous generation NA cars. The NA heads on the RB2X NEOs have MUCH smaller intake port cross sections and are not compatible with any of the aftermarket forward-facing manifolds available for the RB25DET. This can be remedied with a RB25DET NEO head, but those are expensive relative to what they are. A full long-block from a turbo AWD Stagea is generally a better value and will run you about $4000 USD to get it to you. This will get you the stronger RB26DETT rods, as well. That would give you a base to build off of to be safe in the 400whp range. Not shooting for the moon, but if the stock R34 was your bar, this engine would buy you enough to be just North of stock GTR power. A forward facing manifold would allow for the easiest method toward using Bosch EV14 format injectors such as those from Injector Dynamics and FIC, to name a couple. People hate them because they're copies, but Greddy fakes can be had for around $300 USD. With what the fuel rail, regulator, injectors, and the rail adds, figure $2000 USD for the whole setup including the manifold. With the OEM brackets and a bit of trimming to the ends of the lower frame rails, the OEM intercooler mounting brackets can be used to mount an OEM GTR intercooler, or an aftermarket one made for a GTR. Those are handy vs a universale due to the angles that the end tanks have on them. Then your plumbing become super straightforward at that point despite having to cut a hole where the battery is an a matching one on the other side for the pipes. Battery can go to the trunk. I'd round up to a healthy $2000 USD here too (maybe even a tiny more) to allow for a nice aftermarket unit and some pipe fabrication. Or if you can find someone that's upgrading to something larger, the used market comes in clutch here for a decent savings. I won't even get into turbo sizing as that's something that would be for yourself to determine. HOWEVER, for the purposes of your stated goals, a Borg Warner 7064 with an internal wastegate would be a perfect spooler and would make stock GTR power easily. It would also bolt up to your OEM manifold (that would come with the DET you purchased a couple steps above) if it were ordered with a T3 flange. More with adequate fuel. If you can stick with the OEM exhaust manifold then expect to be in the whole about $6000 USD for decent turbo like the one suggested, a down pipe, new O2, and full exhaust to mate up, and upgrades to the integrated BOV in an EFR or a standalone BOV for a different turbo, as well as an aftermarket IWG (internal waste gate). Those last two are definitely optional and unnecessary. All of this stuff above does you no good without any way of tuning and or monitoring the engine. Bite the bullet on a standalone engine management solution. If your experience with wiring is limited, you're going to have to hand it off to someone else, though. Unfortunately, the adapter/patch harnesses available are typically made around the GTT which does not include AWD, and the GTR, which integrates into a lot of chassis features that aren't present in your wiring interface. So the ENR34 is the oddball. So you'll want to expand a bit on your selection and find an ECU that's capable of running the ATTESA pump also. I have a Link Thunder, but you don't need quite that much ECU to accommodate that. You WILL need someone with the know-how to tune it and code those features into whatever software it uses. And to wire it up. This will be your most significant expense. Call it $6000 USD with an ECU, an okay wiring job (no motorsport grade at this price), aftermarket triggers and R35 coils, and the time it takes to tune the ECU with added features (electronic boost control solenoid, MAP, IAT, the new triggers, and ATTESA) and don't be surprised if it's more if you want better work done. Grab a clutch made for any RB pull transmission R32/R33GTR made for the power handling capacity you're looking for. Budget $1500 USD for a new good one. That's about $20,000 USD for an engine you've upgraded yourself and had wired and tuned by someone else. That's no brakes (ENR34 brakes are pathetic), suspension (again, pathetic), or wheels and tires. So you're pretty spot on in terms of spending $30,000 USD extra on the car just to get it to perform a little better than a stock R34 GTR while looking like a bone stock ENR34 with some wheels and suspension mods. That doesn't include fluids, maintenance items, gaskets/seals, repairs needed or anything else discovered along the way. But you'll have a car you can take to the track and have fun without worrying as much about nicks and dings.  
    • Sxnjeet
      Another Crank No start thread - r34 rb20 neo + t

      By Sxnjeet · Posted

      Okay so, please read this. car started and ran fine. got my tuned ecu by RSenthalpy, did a bunch of pulls to test it out and finally drive the car after half a year of it just sitting and idling at most. Everything was good, thing ran flawlessly and had so much power, didn't feel slower than a Prius anymore. Parked it back and turned it off.  Next day, I install an AFR and start the car. Didn't wire anything to the ecu. Just gauge.  Car started, but died out in about a minute. I figured it was cause my car was on a lift and the fuel was really low and old. I add 5 gallons of fuel, still cranks but no start. I remove all AFR wiring (tapped into double din acc and power wires but there was a nest of wiring there so I was worried I messed something up. tried to put it back to how it was prior to afr install.) Still cranks no start. Changed spark plugs with brand new ones Changed fuel pump with a new one (verified working) Did compression test , compression came back all at 150ish. All fuses are good, Relay seemed good but ill double check by switching similar relays around. Verified MAF is working - Ended up getting curious as to why fuel pump is not priming when ignition is on, so I cut the fuel pump ground and power and connected them directly to a portable jumper. I also disconnected fuel line to fuel rail to verify fuel is being sent. So with direct jumper power, the fuel pump turns on and shot gas everywhere through the fuel pipe that I had disconnected, so ny doing that, I verified no clogs in fuel lines or filter. - Tried starting the car with that jumper directly wired to power and ground, but car still did not start. I'm guessing its a CAS issue but im a little scared to check it without messing up timing or anything else since I actually dont understand how to check CAS lol. If anyone has any other suggestions or recommendations , please let me know.
    • sunsetR33
      R33 GTR lift points for hoist

      By sunsetR33 · Posted

      Hi all. I am aware there is lots of discussions about jacking points, where to lift the car and what not. But as usual just a lot of "in my opinion" and nothing definitive, and everyone does it in a different way. I want to hear from some experienced people on which points on the car it's okay/safe/recommended to lift the car using a four point hoist/lift. I will attach some images of my underbody. Sills are largely okayish, the driver side jacking point is pretty mangled though and it looks like the underfloor is slightly pushed in too, but I might be wrong. In the German Skyline forum, the consensus is to use the sidemember chassis rails in the front and the rear subframe? bushing in the rear. I know the manual says to never use the sidemember for loading but lots of folk do it and it was definitely done on my car too as they are slightly bent too. Based on the images, what points do I use to not make the already present damage worse? I'd use wood or rubber blocks to spread the load across a bigger area of course. Driver side sidemember and jacking point mangled one) https://imgur.com/a/eKjzrJX Driver side rear jacking point https://imgur.com/a/W3DWF1P Passenger side sidemember and jacking point https://imgur.com/a/65UvIJe Passenger side rear jacking point https://imgur.com/a/h3k7j53 We can also see some underbody rust but so far it all looks somewhat treatable and nothing that requires a Yoshida style restoration.
    • MBS206
      Ticking Sound On Idle - Rb25

      By MBS206 · Posted

      Have you put an aftermarket oil pressure gauge on and verified your oil pressure?   Noise being on the block, on exhaust side, how high up the block does it seem to be? It could be the VCT system getting cranky, especially if it's mainly at idle, and when warm, as that'll be your lowest point for oil pressure. Could be showing that oil passages / VCT solenoid are blocking.
    • WARLORD
      injectors top feed for sale

      By WARLORD · Posted

      Deatschwerks 1800cc sold
×
×
  • Create New...