Jump to content
SAU Community

Recommended Posts

Hey guy,

can someone give me a hand, i am going to install the safc tomorow although,

the manual doesnt match the wiring coming out of the safc lol so i am a lil confused.

can someone take a pic of there ecu and tell me what wires go where. or give me a lil run down.

few things i am unsure about is what wire should be going into the throttle wire on ecu. and someone told me a whire should be going into the knock sensor wire on the ecu also, but this isnt in the manual.

which makes me confused.

my car is a r33 gts-t

thanks

Link to comment
https://www.sau.com.au/forums/topic/67027-safc-install-help-needed/
Share on other sites

G'day,

I recently wired a SAFC (blue screen version 1) into my ca18det S13 so I can give you my experience with this unit and hopefully answer some questions. The SAFC doesn't have a knock sensor function (the SAFC2 does) so you won't find a wiring diagram showing it.

Your SAFC should have 10 wires - red, green,grey,black.brown,yellow,white,blue,pink and orange. For your R33 gts-t you won't use the blue, pink or orange wires. The grey wire is the throttle position sensor input. Red is +12V power, balck and brown are ground, green is RPM, white is AFM input and yellow is AFM output.

I recommend you go to the Apexi website www.apexi-usa.com and download the 2 PDF files from the documentation page called electronics_safc_ins.pdf and electronics_safc_wire.pdf. These contain all the information you need. Make sure you read all the warnings before you attempt to install it.

Hope this helps

Kris

i just installed my safc on friday night. d/l the 2 pdf's and its alot easier. it has 2 diagrams for rb25, one for ser 1, one for ser 2, however they are both the same.

also look closely at the wiring and the locations in the connector. there was a few times i questioned which wire it was.

dont rush it and u'll be fine.

cheers

Linton

if you are not busy today i could have a look at it for you as i fitted one to SKA's 33 gtst not long ago..

if your afm isnt workin you would have had troble before you fitted the safc-1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi. A little bit of an update. It maybe(hope not) looks like i would need a new tranny(it would be "maybe" a cheaper or better option anyway) So i need some info. I know i need a different propshaft(i can make custom one) LSD is not a problem cuz the engine will be still(for now) N/A RB20. So if i buy RB25DET NEO tranny...is there something else i need? I read something about push/pull type but i do not know if i need to "change" something or i can just plug n play onto my engine a go? Thanks for the advice  
    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
×
×
  • Create New...