Jump to content
SAU Community

Recommended Posts

  • Replies 295
  • Created
  • Last Reply

Top Posters In This Topic

Yeah, too easy man... waitara macas is the one on the pacific hwy opposite auto one near hornsby. but yeah, if you wanna come to my place we can head over there together, PM me and lemme kno :P

talk about mini-cruise...hornsby to waitara...enjoy the 30sec drive. Actually I want be a part of this historic 30second cruise.

I'll most likely be there, might also bring along another 33 and a 32 if I can!

anyone from around st george area would to meet up and cruise in together?

hey mate i'm from strathfield u can come down king georges and i'll meet u in the BP just before punchbowl road if u want... or at the shell with lonestar near hume hwy then we can make our way up

talk about mini-cruise...hornsby to waitara...enjoy the 30sec drive. Actually I want be a part of this historic 30second cruise.  

I'll most likely be there, might also bring along another 33 and a 32 if I can!

lol will do dave..

liz i have no idea where wailtara is..lol

that;s why

talk about mini-cruise...hornsby to waitara...enjoy the 30sec drive. Actually I want be a part of this historic 30second cruise.  

I'll most likely be there, might also bring along another 33 and a 32 if I can!

Ha ha! sold! lets all meet up at my place and have a mini-cruise to maccas :)

and it'll be at least a minute long :P lol!

is it meet up at thornleigh or waitara?

is waitara maccas the one opposite repco and bridgestone or something?

Waitara Maccas and yeap! that's the one :rant:

Liz :D The cruise goes a lil more then 1 min :rofl: ...

Neway , so its still 930 Waitara maccas meetup ?

Liz was refering to the mini cruise from my place to maccas :):P

Meet point will be Waitara Maccas at 9pm for a 9:30pm departure.
;)



  • Similar Content

  • Latest Posts

    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
    • What are your thoughts on this after having it for a while, worth getting?
    • Downshifts are harder on transmissions than upshifts, the input shaft naturally slows down once disconnected from the engine so the synchros aren't doing all the work. There's no "natural" tendency for an input shaft to increase RPM. Something is not right there, I don't have a great answer on what. You can try a dedicated GL4 75W90, I plan to switch to Motorcraft XT-M5-QS which is supposedly a very good 75W90 for NB Miatas which have a weirdly sensitive transmission from the factory. I would chase down why your clutch is making a hissing noise, that's not normal. It might be no big deal but in the absence of anything else to investigate I would look at that.
×
×
  • Create New...