Jump to content
SAU Community

Recommended Posts

  • Replies 295
  • Created
  • Last Reply

Top Posters In This Topic

well i polished my car today so i spose i had better come.......

Got a white R32 gts-t with a GTR kit.... fooley sick

oh where is a good meetup spot that i can find.... im coming from the east and have no clue on how to get to thornleigh maccas? and western meetin spots or city ones?? im lost....

see u all there

ed

Someone SMS'd me today from SAU , and i rang the number back and i SWEAR i must of typed the number in wrong or something cause i got some non-English speaking persons ;) . I was talking about " oh its Bizzr from SAU , Are u coming to cruise " he had no idea wat i was on about . :) silly me hope i find out who it was then

Ya westies are meetin @ rouse hill maccaz, the one near Ettamoga pub .

Then meeting 1 more just off M2 and pennet hills rd then off to Waitara.

I hope we do stop for some nice relax time :) be that food and drink or just a mingle for a while , im in no hurry really and i guess driving all the way there and bak would be pretty lame ;)

are there any plans to get food during the night? or should we turn up with a full stomach?!

hopefully either the pizza place or the fish and chip place in newport will still be open, but not sure. We can alway go for a maccas run...

Hey Ed. I live in north sydney if u wanna meet up b4 i can show u the way to waitara.

Ya westies are meetin @ rouse hill maccaz, the one near Ettamoga pub .  

Then meeting 1 more just off M2 and pennet hills rd then off to Waitara

Where abouts are you meeting "just off the M2"? And what time?

If all works out well tomorrow, me and the misses may tag along for this as well.

hopefully either the pizza place or the fish and chip place in newport will still be open, but not sure.  We can alway go for a maccas run...

Hey Ed. I live in north sydney if u wanna meet up b4 i can show u the way to waitara.

im there...

where to meet?

Ok.. I still haven't got my car back yet... its been at mechanic for 2 days now doing early 100,000K service... changing a hell lot of things... should be able to get it back today..... :goddam:

I'm going to be at Thornleigh Maccas at around 8:40

and head over to Waitara Maccas at around 8:55

Cruise or not will decide by then

So if anyone would like to meet at Thornleigh Maccas first

I'll be in a White R33 S2, be nice COME say HI to me...

Cheers

Sam




  • Similar Content

  • Latest Posts

    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
×
×
  • Create New...