Jump to content
SAU Community

Recommended Posts

Hi,

Thinking of upgrading the fuel pumps in both our GTSTs. Currently the 040 is looking to be the replacement because of the price and ease of installation. Just waneed to know if they are much louder (as compared to a GTR pump), or if anyone's had any problems starting their car after installation..

I remember reading on here a while ago that someone had to crank their car several times before it started after installing an 040 - or was that a one off.

Also, as a replacement for a car pushing 300kw, would the 040 flow enough?

Cheers!

Link to comment
https://www.sau.com.au/forums/topic/67838-upgrading-gtst-fuel-pump/
Share on other sites

i used a 984 (i think these are used in porsche turbos ?!?). they are just smaller than the 044 lengthways, and should flow more than the 040 from the bosch pump link (driftkng has it on his for pumps 4 sale ad).

if u want the most headroom then 044 is the way to go.

the 984 makes some noise compared to the factory pump but i have written an install guide in the DIY section which may help explain it a way to minimise it.

ps. did u buy that IC??

I've had an 040 in my car for about 1yr now.

It's certainly harder to start (you have to switch the ignition on, wait for the fuel pump to click off and then turn the key over).

I can hear the pump but -only- when starting my car at midnight in the garage with the roller doors shut (ie, you can't hear it out on the street).

I have a bosch 910 installed externally

It starts fine

I dont wait for the pump to click off before I start, is this bad?

It makes a slight buzzing noise in the cabin barely noticable if you have the parcel shelf and rear seats on. But lately at idle it seems to be buzzing louder than usual, Im not sure why either... hope its not dying :wassup:

I've had an 040 in my car for about 1yr now.

It's certainly harder to start (you have to switch the ignition on, wait for the fuel pump to click off and then turn the key over).

I can hear the pump but -only- when starting my car at midnight in the garage with the roller doors shut (ie, you can't hear it out on the street).

Yeah I think it was your post I saw, plus a mate of mine who got a Bosch pump (not sure which model) had the same thing happen.

I'd say the problems with the cars not starting would be the check valve wasn't installed on the pump when installed. If you don't do this the pump has to re-prime the system once the car has been left for awhile.

Below is a photo of the 044 we installed in my r33 four weeks ago - I didn't install the check valve so will have to fix this when I get round to it.

The 044 only just fits into the tank and was a pain in the arse job so if I did it again I'd keep the factory pump intank as a lift pump then use the aftermarket one externally.

Good luck.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The cam I am actually putting in (a few posts up) is actually smaller than my current one. At least duration/overlap wise. All the chop stuff I hear just sounds like an engine running badly, because it is. I then envision driving it around in 1st gear and being massively sad about it bucking to the beat of said chop. There is an idle video of someone with a similar cam floating around the internet, but mine is a custom cam (so is his) so it'll never be the same, plus the fact exhausts are entirely different. What I want to do is put some bullet mufflers/race mufflers in to replace a couple sections straight pipes that currently replace the two extra cats that I don't need. But this is even further down the line!
    • I can tell you now, when the bracket that the little hydraulic ram attaches to snaps, with a subframe, and V8 from an AMG C63 on it, it sounds like someone letting shotgun off right beside you. It leaves your ears ringing, and a huge thankfulness that you never ever put a body part under something heavy that's only supported by a hydraulic lift...
    • Still not a guarantee fix. I used a high quality butyl-mastiq (the black goo that's not really silicone nor polyurethane, same stuff they use from the factory that just spreads out like melty cheese), and I still get lots of water on both sides of the trunk when raining or washing the car. I also suspect the factory spoiler rubber gasket might not be sealing well, so I'm thinking of adding a thin layer of grey silicone around the bolt holes on both sides and see if that's where it also leaks from. The biggest issue is that these cars don't come with a drain hole on each side like other coupes and hatchbacks.
    • I hate it, but maybe he could paint it Monster jam style and call it...godzilla?
    • Would seem to me to be appropriate to go GTR style bar. There are options with and without N1 vent holes, with the GTR lower lip integral (because FG copy). https://justjap.com/search?q=r32 bumper  
×
×
  • Create New...