Jump to content
SAU Community

Recommended Posts

hey every1,

mah cousin recently entered the exciting world of skyline ownership & after seeing my car bought herself a nice R33, excellent condition an really low Ks. BUT I noticed that her wheels only have 4 studs/spokes. I'm confused as I have only ever seen R33s with 5 studs on the wheel, She's not really into cars so she's got no idea either (bought it coz she thinks itz sexy). I'm just wondering if this is normal or if the dealership sold my cousin a shifty skyline.

I'm also a little concerned about how the car is a 1993 but only has about 66,000kms on the meter :uhh:

Her car is a 1993 series 1 R33 coupe, N/A though

What's your opinion?

Link to comment
https://www.sau.com.au/forums/topic/68001-is-this-normal/
Share on other sites

  ApleX said:
when i was looking for my r33 there were heaps with very low KM eg 52 and 60 to me they all just seemed abit sus.  if its a 93 the car has only done 5000km a year. thats less than 100 a week. She could be lucky but then again there are lots of dodgy bastereds out there

I drive around 100ks a week.

Link to comment
https://www.sau.com.au/forums/topic/68001-is-this-normal/#findComment-1261096
Share on other sites

  PLYNX said:
And I hope she didnt think it was a turbo that she was buying and got ripped off !

aww nah she knows what a turbo sounds like thanx to my car :wassup: but her folks didn't want her to get a turbocharged car, an her insurance is heaps cheapa den mine

As fer da really low k's the car looks really top notch. a few scratches on the side of the bumper but that's understandable. As fer performance the engine bay looks well maintained an it runs smoothly an quietly, all points that this car is on the level :(

It'll make fer a really nice daily driver

Link to comment
https://www.sau.com.au/forums/topic/68001-is-this-normal/#findComment-1262426
Share on other sites

last night i made it to 360kms when the needle was below the 'E' on the fuel gauge.. was basically driving slowly up hill and letting it roll in neutral downhill :rofl:

360kms in 53L - crap. :P

i think it's getting worse now.. i drove about 50kms and it's dropped from full to halfway between full and the second line - i wasnt even driving it hard AT ALL last night :

Link to comment
https://www.sau.com.au/forums/topic/68001-is-this-normal/#findComment-1265583
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Not sure what you mean by electronic speedo drive.  Speedo reads fine up to 180 yes.
    • For anyone interested, this is my old graph from 2021, but I've plotted the previous setup curve onto it with a black pen. old setup was: pon cams, oem itbs and plenum, HPI manifold, hks 2835 pro S .87ar rear, Turbosmart actuator, 3" turbo back no res. or cat., greddy spec M fmic, nismo 740cc inj, walbro in tank 460, splitfires, 4" intake pipe, Apexi pod, e85, eboost2, power Fc. I love that the new setup has much larger turbo spec with the HTA3076 1.01ar Ts rear, and literally everything is bigger, but far higher quality and result is it's FAR more responsive in paper.
    • This makes a lot of sense! I just had that realisation a few minutes ago and wrote it above haha. This is a good new discovery. "Sanding the side of the hill" perfect way to put it.   馃槀 馃槀 
    • This is probably what's happened to me. I'll put filler again on my repairs and use the long block and let you know how I go. Fingers crossed it's my last batch of filler lol. I can see that happening where my block dipped at certain points because it didn't cover all the high spots at the same time if that makes sense. I'm just trying to visualise the fact that with the large sanding block I will be sanding far away from the central dent area and whether that will cause issues or whether that's going to fether out my repairs better.
  • Create New...